Search results

  1. S

    New truck, trying to understand its molestation - carb/intake

    yore carb has a standard q jet bolt pattern .only way you will know whots under it is to remove it .we had an 86 in recently looks the same as yore set up carb vack lines an all should you need to nremove the throttle bracket thears a bolt in rear of drivers side cylinder head .good luck
  2. S

    No Spark, No clue...

    sum time ago we had a truck in from an importer ran fine then went to move it and it would not start i remember the five pin modual was suspected picked up a new one no diffrence .i found a wire from the five pin plug that went down the bulk hesd .this was melted on manifold replaced it and away...
  3. S

    Gas Evaporation?

    i thort he said rusty cap .maybe i read wrong ! but sad to say it stoped disapearing fule .sum scum bag helping them selves coz thay to good togo pay for thear fule same as the rest of us
  4. S

    Gas Evaporation?

    i had the same thing hapening to my truck .i fited a locking cap and it stoped .
  5. S

    Does anyone know what this is

    well did any one actual find out whot it wos .i ma have been wrong on how the switch works but i wos tring to help .isent this whot thease forums are about .sory burrban im an idiot and thanks for bukket to pointing it out
  6. S

    CAM ADVICE

    hi all thanks for input masking tape fixes most wounds ! ok as promised the heads are 14096217 55-86 350ci 285-300 hp crate engine 64cc chambers thats whot it said so my block and heads are a difrent year are thease heads an good ? as i said i dont want a race engine but i dont want a slug ...
  7. S

    Does anyone know what this is

    i have an 88 firebird with tbi oil sender is behind dizzy the one in the side is a pressure switch so fule pump wont run with no oil pressure
  8. S

    CAM ADVICE

    ok thanks the engine is a 87-95 350ci with one peice seal and roller cam.dus not have vortec heads only id on block is 5.7 lg on side next to front of startor is 638 cast on block i beleve that the single piece rear seal and the casting for the roller cam spider drilled or not started in 86...
  9. S

    CAM ADVICE

    HI ALL i have a 84 c 20 and the engine is not well .good news i have a 87 engine that needs a rebuild .not a problem pistons crank polish bores etc etc ok now the problem whot cam do i put in it .this block has a one piece seal and a roller cam id like to stick with the roller cam but which one...
  10. S

    Here I go again, ANOTHER junk 350 block .................

    could you not ship a block to the machine shop?
  11. S

    Cam suggestions?

    good stuff onc ive finished the wiring ! im looking to fit a 88 block with roller cam and vortec heads
  12. S

    Am I Cursed by the Carburetor Gods? Or do I just suck with Carburetors?

    check the carb to manifold gasket .make sure it seals the carb to manifold no open air ways .dont ask how i descoverd this !
  13. S

    Fuseblock failure - What can go bad to cause it?

    i had water leaking from the bulk head seam .straight into fuse bord. FANTASTIC !
  14. S

    8 bolt rims that are 16" & will fit hubcaps.....??

    HI ive just shiped a wheel to the uk from santa ana wheel .may be worth a look verry helpful .
  15. S

    serpentine upgrade, fan almost went through hood. Anyone done this with a flex fan?? pics inside

    HI i thort the serp pump ran the oposite direction !
  16. S

    Carb to TBI Conversion

    HI sorry how do i pm you ?
  17. S

    c20 8 lug

    thanks everybody i have one on its way .the 16.5 has made a nice plant pot !
  18. S

    Fitech

    HI ive git same setup on my firebird found that o2 sensor works best in a balance pipe or the system ran rich as hell .
  19. S

    c20 8 lug

    HI im in the uk so not easy to find .i have a 84 c20 with 16" 8 lug steel wheels ive recently imported one to find the tyre dus not fit the tyre shop said its a 16.5 ! can any one give me an idea as to whear i can get the corect wheel and someone willing to ship to the uk thanks steve
  20. S

    Carb to TBI Conversion

    HI all im new hear ! i have recently purchased a 84 c20 with a 350 .im looking to convert from the rochester to a tbi set up which i hve from an 88 firebird with a 305 complet set up .dus anybody know whot willneed to be changed to make this work on my 350 any help will be gratfully receved.steve
View older results

Latest posts

Forum statistics

Threads
44,167
Posts
950,743
Members
36,282
Latest member
Doug Hampton
Top