Search results
-
no power to anything in cab
I tested at the fuse block (inside) and am getting power to several but not all fuses. I'm having trouble reading what the fuses go to since the letters are worn. I am getting continuity over the tootsie roll fusible link and the wire from the tootsie roll fusible link is getting power at fuse...- curse
- Post #6
- Forum: Electrical & Audio
-
no power to anything in cab
Yes I checked the fuses and they look good. I pulled each one out and looked at them. I will see if I can find the tootsie roll, my wiring harness has been chopped up so bad I'm tempted to replace it, when I have time I'll hit the junkyards.- curse
- Post #4
- Forum: Electrical & Audio
-
no power to anything in cab
79 c10. I have no power to the headlight switch, wiper switch, blower motor. I have zero exterior lights. The only thing my truck will do is start and run. I've been searching the forum and googling without much luck. Is there a fusible link for all these? If so where is it located, at that...- curse
- Thread
- Replies: 20
- Forum: Electrical & Audio
-
cannot get brakes to pump up 79 square
I was opening the bleeder screws on wheel cylinders with a wrench and when the wrench hit the axle I figured it was far enough. It was about a quarter turn but no brake fluid would come out. I tried bleeding again today but when the wrench hit the axle I removed the wrench and turned the... -
cannot get brakes to pump up 79 square
Yes I did. Funny thing is the pedal would pump up before I replaced everything. -
cannot get brakes to pump up 79 square
I replaced the master cylinder with a new one about a year ago. I haven't driven it any distance since I've been repairing other things. replaced rear shoes, rear wheel cylinders, rear rubber brake hose, both rear solid lines, and solid lines from rear to the prop valve. I removed the switch... -
1974 Chevrolet C10 Stepside Build....
FWIW I installed a 700r4 using the stock crossmember on my 79 with no clearance issues.- curse
- Post #109
- Forum: Tech Discussion
-
Rust around windshield, what is the best option to repair?
Free if you come to Michigan and pick it up!- curse
- Post #9
- Forum: Paint and Body
-
-
-
-
Can you build a new box from lmc truck?
The guy on Indianapolis CL is actually east of Pittsburgh PA. About 6-7 hour drive one way. -
no fluid to right caliper
Confirmed, shut solid at the bracket.- curse
- Post #17
- Forum: Suspension, Steering & Brakes
-
no fluid to right caliper
I still want to dissect mine- curse
- Post #16
- Forum: Suspension, Steering & Brakes
-
Any tips on removing old brake hoses?
I just did mine today. I removed the horseshoe clip on the rubber end of the line where it goes through the frame. Then I was able to push the brake line in towards the engine bay, this gave me better access to where the metal line goes into rubber line. I used a 16mm and vice grips to get them... -
no fluid to right caliper
It was the hose, what a pain in the butt when it's rusty- curse
- Post #14
- Forum: Suspension, Steering & Brakes
-
no fluid to right caliper
Makes sense, i've never seen or had a hose go bad by swelling. Maybe I finally will.- curse
- Post #13
- Forum: Suspension, Steering & Brakes
-
-
no fluid to right caliper
I'll unhook the hose where I have metal line and see what happens. It did sit over 3 years. When I unhooked the line from the caliper I expected some fluid, even if not a lot, but I didn't get 1 drop. With the line unhooked I had my neighbor push the pedal and there was still nothing. I was...- curse
- Post #5
- Forum: Suspension, Steering & Brakes
-
no fluid to right caliper
I know the proportioning valve balances the fluid front to back but can a bad valve block fluid to right front caliper? Fluid gets to the rears. Master cylinder leaked and I replaced it.- curse
- Thread
- Replies: 17
- Forum: Suspension, Steering & Brakes
-
-
-
-
-
problem getting 350 started
The cause is my forgetfulness and I must have not adjusted them- curse
- Post #122
- Forum: Engine & Performance
