Search results
-
P
What have you done to your square lately??
Any chance exhaust shop melt a wire? Assume engine ran when loaded on trailer? Sent from my moto g power using Tapatalk -
P
Hello from France
Welcome from coastal Georgia USA!! Nice truck- Poppy 87
- Post #16
- Forum: Introduction
-
P
What have you done to your square lately??
You might want to put some anti seize compound on prior to reinstallation this time. Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
That is the a/c compressor clutch that cycles on demand -
P
What have you done to your square lately??
Here are the covers that I bought new in 1982ish. No Holley identification other than the box Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
I have a similar set, still new in the box! Got them in 1982, box says Holley on it Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
Spoken like someone who doesn't get their hands dirty! There are crooked mechanics, heck, there's crooks in all industries, but I wish you success in your truck repair. I comment as a technician with over 35 years experience and know that about 2/3 of guys in the industry can't properly diagnose... -
P
What have you done to your square lately??
Brother, you are a totally cool grandpa! I hope to similar for my grandkids, the oldest of the three turns 9 tomorrow so I have a few years Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
Transmission fluid expands as it heats up. Start your truck cold, check fluid level, add if necessary to the bottom of the cross hatch area on dip stick. Go on a test drive 10-15 miles to warm up the transmission fluid and check level again. This is where you bring fluid to the "full" mark by... -
P
What have you done to your square lately??
Doug, as long as you have the correct dipstick, on a level surface (your oil stained driveway), start it up and check fluid level. If no indication on stick, I add in 1/2 quart (pint) increments until the "full cold" mark. Drive it around a little bit, Home Depot run, beer run, then check when... -
P
What have you done to your square lately??
GM change to Dexron VI back in 2006, it is still red in color, and is compatible in all 3 and 4 speed automatic transmissions. It is also used in the 6 speed automatic transmissions as well as the Allison 5 and 6 speed. The late model 8,9, and 10 speed automatic transmissions use a completely... -
P
Hello all, anyone know how to verify a Spirit of 76' model?
Welcome from Georgia!!- Poppy 87
- Post #10
- Forum: Introduction
-
P
New to the forum - I have a 76 Sierra 15
Welcome from coastal Georgia!!- Poppy 87
- Post #9
- Forum: Introduction
-
P
What have you done to your square lately??
Screw that, I love Mexican food! So does the wife so I guess she puts up with the rear end whine -
P
What have you done to your square lately??
I don't think that is correct. Short of an improperly set up differential, (pinion depth, pre-load, back lash) any "movement" would be negligible. Sent from my moto g power using Tapatalk -
P
Engine stumble
Be sure to add fresh gasoline and fuel filter to the things listed previously- Poppy 87
- Post #7
- Forum: Tech Discussion
-
P
What have you done to your square lately??
Welcome to my world! Some may just live with the oil leak... The joy of owning classic vehicle Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
An old school technique is to chain the spring to the frame prior to ball joint separation Sent from my moto g power using Tapatalk -
P
77 K10 LS Swap
I have one made by Pyle that I fit on a non square body truck to assist the wife while connecting her camper. This unit is wireless, the screen is the size of a cell phone and camera mount to the license plate bracket. It's ok, but only used for the above mentioned task. Probably paid $100 ish ...- Poppy 87
- Post #457
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
P
What have you done to your square lately??
I would bet that cylinder head weighs more than Natalie! Sent from my XT1254 using Tapatalk -
P
Pcv or not to pcv?
Pretty sure the cat lands on it's feet regardless of age or where the bread is tied- Poppy 87
- Post #117
- Forum: Carb Fuel Systems
-
P
My truck runs! Stopping? Eh not so good
You absolutely should "bench bleed" the master cylinder. Not sure what method that you prefer, but might consider gravity bleed method if in no hurry followed by conventional brake hydraulic method. You may want to consider "flare nut" wrenches so you don't round out brake line fittings if you...- Poppy 87
- Post #2
- Forum: Tech Discussion
