Search results
-
P
What have you done to your square lately??
Are you sure that the adjusters are in their correct position and not swapped side to side? Sent from my moto g power using Tapatalk -
P
What have you done to your square lately??
Young man, you take care of yourself. I bet your truck will be just fine as she sits Sent from my moto g power using Tapatalk -
P
cannot get brakes to pump up 79 square
Did you bench-bleed the master cylinder prior to installation? -
P
Decent Paint Job
I'm with you on this! I know so much of a really good paint job is prep work. A friend of mine that paint's show quality cars said he would do my truck, but would need it for a year. He suggest Maaco if you can get a reference from a decent one, as those guys shoot lots of paint and it's usually...- Poppy 87
- Post #6
- Forum: Paint and Body
-
P
Engine shut off while driving my '90 Suburban. Sup with that?
I would only use ac delco ignition control module. Do not ever cheap out on electrical components- Poppy 87
- Post #6
- Forum: Engine & Performance
-
P
New here, just introducing myself and vehicle.
Welcome from Georgia!! Nice truck. Lots of Texans here- Poppy 87
- Post #16
- Forum: Introduction
-
P
Toggle Switch Mounting Locations?
How about steering wheel switches like later model trucks use?- Poppy 87
- Post #10
- Forum: Tech Discussion
-
P
Front Driveshaft Seal
Thinking there is an o'ring there. I would check with a drive shaft shop.- Poppy 87
- Post #2
- Forum: Differential & Driveline
-
P
Floor Shifter For TH400
Not necessarily, but that shifter will not fail, ever! Sent from my moto g power using Tapatalk- Poppy 87
- Post #12
- Forum: Automatic Transmission
-
P
Floor Shifter For TH400
Go old school, Hurst Quarter Stick- Poppy 87
- Post #3
- Forum: Automatic Transmission
-
P
What have you done to your square lately??
Zach, those engines rarely have injector failure. You can do the noid test again to verify, but I bet it's mechanical. Pull the valve cover and examine the valve springs on #2 VERY closely as it is not uncommon for them to break. A running compression test may also work. Been working on these... -
P
What have you done to your square lately??
Dang, how much $$ to powder coat brake drums -
P
What have you done to your square lately??
It happens Zach, figured it was electrical when you post those dtc's. Glad it was a simple fix -
P
What have you done to your square lately??
Zach, it sure appears to be an electrical concern to me. I would ring out all wiring going to the transmission connector. Didn't you just have a fuel pump wiring concern as well? -
P
TH350C been sitting a few years
To the OP, unless you know it was drive able prior to purchase, and you are capable of rebuilding this transmission, I would rebuild it now while the engine is out of truck. You then know things are all good.- Poppy 87
- Post #11
- Forum: Automatic Transmission
-
P
TH350C been sitting a few years
The "C" indicates clutch, as in lock up torque converter (TCC)- Poppy 87
- Post #9
- Forum: Automatic Transmission
-
P
FNG from Denton TX
Welcome from Georgia!! Sent from my moto g power using Tapatalk- Poppy 87
- Post #5
- Forum: Introduction
-
P
What have you done to your square lately??
You have any pictures of the set up? Awesome idea! -
P
What have you done to your square lately??
There is no such thing as too much cooling for an automatic transmission. If you already have it, and are installing the new radiator/fans install it. That's what I would do. May want to install a transmission temperature gauge as well. Easy for me to spend your time and money though! -
P
28 or 30 Spline Information
Welcome from Georgia!! Probably 28 spline- Poppy 87
- Post #4
- Forum: Differential & Driveline
-
P
S10 driveshaft replacement question
Ted, if you have a torch, heat the ends of the shaft where that poly glue stuff is and it will melt and run out thru the small openings on the yoke ends. Make sure to allow it to cool to room temp, then normal u-joint replacement methods work. Without a press you can use a vice and combination...- Poppy 87
- Post #28
- Forum: Differential & Driveline
