Search results

  1. Mark Jones

    My Rear End Build For My Low Buck Street/Race Truck

    I'm thinking possibly I might have a 10 sec shop truck here..................
  2. Mark Jones

    My Rear End Build For My Low Buck Street/Race Truck

  3. Mark Jones

    My Rear End Build For My Low Buck Street/Race Truck

    New best: 1.50 60 foot 7.04 660 94.19 MPH 660
  4. Mark Jones

    Newbie doing 454 swap need some guidance

    467 CU IN 9.3 Compression 236 headed ported peanut port engine, 228/238 @ .050 hyd roller cam, stamped steel rocker arms, Performer RPM intake, modified factory 4 quart oil pan. Dyno test below.
  5. Mark Jones

    Peanut Port #14092360

    Here some information you can use. Those 360s are peanut port heads with stellite seats. Any factory carburated stock 454 engine made 320 HP with headers on the dyno. Properly done 9.3 comp, 228 @ .050 cammed 454s can perform like this: Not sure what can be done with the TBI 454.
  6. Mark Jones

    Blue Print or GM Performance

    Great install!
  7. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Thanks, I had Larry Meaux port these heads, he did a good job.
  8. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Ran a new best today: 7.04 @ 94.15 1/8 mile 1.50 60 foot So close to having a 10 sec truck, its making me want to do just a little more............
  9. Mark Jones

    400 SBC Build - Tight Budget

    First step here is to mag the steam holes for cracks, you have rebuilder special here, so it needs decked and honed to .040 with TQ plate. Line hone next.
  10. Mark Jones

    400 SBC Build - Tight Budget

    A well done 400 gets on most BBCs, and smokes a 383, before there was an aftermarket I was running 9s NA with production 400 blocks and small tires at full weight. I didn't use the 5.560 rods though, but I did use 350 5.7 rods. My 400s never ran hot and I've run them on the street, 160 degrees...
  11. Mark Jones

    400 SBC Build - Tight Budget

    Oh that can be done, my trucks 350 made 537 HP with production iron heads, but not for 5000.00
  12. Mark Jones

    400 SBC Build - Tight Budget

    "I need the 4 - 5k to cover the following: (is this even possible)" NO
  13. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

  14. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Spring damage
  15. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Well I got Shop/Race truck to the track today. As usual the condition were good not great. I ran the truck as I drive it on the street, power steering and all. 1325 DA 29.52 Barometer 70 GOW Run 1. 60 foot 1.59 660. 7.28 660 MPH 92.7 Run 2. 60 foot 1.42 rolled the light, foot brake...
  16. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    My suspension is stock, my previous 327 ran 11.97 with a 1.63 60 foot. My new 350 has 90 more HP than the 327 and 104 TQ more. We also built a race trans, with a 2.75 low gear, my old trans the high gear was applying while in 1st gear. I now have a 20 % increase of power at the rear wheels...
  17. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Ok, the new engine is installed and running, should have some track times soon when the track opens. One thing I noticed is it spins the slicks in high gear from a roll now, it didn't do that before. From my estimation I put 20% more TQ to the rear wheels on this build. Shooting for 11s in...
  18. Mark Jones

    Power steering pump bracket for heads without accessory holes.

    The bolt threads into a nut behind the alternator, I use 2 brackets tig welded together for extra strength. You can actually see this in the first picture if you look hard. NO------------problem.
  19. Mark Jones

    Power steering pump bracket for heads without accessory holes.

    !972 Nova power steering brackets, and alternator brackets, 1969 Z/28 pulleys. Works flawless, and I run it hard.
  20. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    HP 6400 RPM TQ 5000 RPM
  21. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    HP 6400 RPM TQ 5000 RPM
  22. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Dyno test of the new 350 537 HP 504 TQ Looks like my truck is going to run mid 11s. My old 327 made: 447 HP 400 TQ Now the question is: will it run 1.4 60 foots with the factory 2 piece drive shaft?
  23. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Done, now dyno testing then installing it in the truck.
  24. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    I like production parts, no rules, I just want the engine to look like my older 327 did. I drive this truck a lot and enjoy it, its certainly no show truck, we just like it how it is, a picture of the old 327.
  25. Mark Jones

    1979 Big 10 Engine & Transmission Upgrade

    Cam is a solid flat tappet 264 @ .050 .528 net lift, 108 lobe separation, with a 1.5 rocker, might go 1.6 on the intake, very mild lobes that will live on the street. My 327s cam was 480 240 @ .050.

Latest posts

Forum statistics

Threads
44,166
Posts
950,714
Members
36,280
Latest member
rodfarm
Top