Search results

  1. B

    6” Rough Country

    My K20 has a 6” BDS all spring lift kit and with street tires (32”) it will just clear getting into my garage 7’ door. With my 37” swampers I would say about 7’1” - 7’2”.
  2. B

    4" or 6" lift for 3/4 ton??

    Bucket, the BDS are stiff compared to skyjacker “soft ride” that my buddy has. I would not say they are horrible but i wouldn’t consider them like factory. A buddy had a BDS for his wrangler that was a daily driver and it was not a bad ride and better than my K20. Don’t know if being a 6” lift...
  3. B

    4" or 6" lift for 3/4 ton??

    I have a K20 with a BDS 6” lift and run super swamper IROKs 36” (actually measure almost 37”). I still have the front sway bar connected and the BDS lift is stiff. I only had to do very minor trimming on the rear of the front fender. I mostly play in the mud and maybe a little hill climbing/...
  4. B

    Body Work & Welding Options

    I went with a klutch 140 mig inverter mig welder from Northern tool and I have been happy with it. It has infinite controls, which is something you don't really get with most welders in the cheaper price ranges, which helps doing sheet metal work. It is 110v, can use flux core or hook up gas...
  5. B

    Best mud tire?

    I run super swamper IROK's 36"x13.5x16.5" when I am on the trial and so far I like them. The IROKs are pretty loud on the street and I don't worry about mpg's since it is single digits anyways! Can't really tell you about longevity since I have a seperate set of tires for the street/ highway and...
  6. B

    Drive line vibration

    When was the last time you had your motor mounts and tranny mount replaced? I had a similar vibration and it was from the u-joints in the front driveshaft. Though I see you have already replaced your u-joints. Replacing my mounts also helped with vibration.
  7. B

    Is anyone still running full time 4WD?

    I am still running full time 4wd and will until it blows up! Thought I am thinking about making it a twin stick set up.
  8. B

    Ingersol Rand / Campell Hausfeld

    I had researched this topic not to long ago and found that the consumer level stuff for IR has gone down hill. I had an oiless small CH compressor that I abused the hell out of and it has run for 25 years! I myself decided to go with a puma two stage 40 gallon unit. Couldn’t find much info on it...
  9. B

    Cam swap

    I am not super knowledgeable about cams and as others have said every setup is different. I will say I am running a small Lunati Voodoo cam. My 350 is mostly stock and I like this cam a lot! Very smooth running and good torque! I would probably say call the cam maker and ask for their suggestion
  10. B

    Welder Question

    I bought a northern tool Klutch brand inverter mig which I like for sheet metal. It can do flux and also comes with a regulator for gas. $400 and a 3 year warranty. It is 110v and I have had no issues with it.
  11. B

    Which is stronger in 4lo, 700r4 or th400?

    I say just run the 700r4 till it blows up! In 4lo All the time I doubt it will be a issue hauling fishing nets. You will not make much money off a 700r4. I bought my K20 it has a 350/th350/np203 that I run in the mud mostly and some trails and figured I would upgrade as I blew stuff up. I have...
  12. B

    Garage Heater Question

    I agree about the propane as being expensive way to go! $$$ A buddy of mine uses propane and he spends a lot in the winter. Have you thought about a pellet stove? I guess you would have to check with the insurance company. They usually have small clearance requirements on the sides and back for...
  13. B

    Dreaded.... which cam should I get question!

    Hi 4wdkc, when you say first cam do you mean the lunati? I have not fully decided yet, thanks for the input!
  14. B

    Dreaded.... which cam should I get question!

    Thanks everyone for the replys!
  15. B

    Dreaded.... which cam should I get question!

    Thanks for the input everyone! Looks like I am leaning towards the comp cams 12-300-4
  16. B

    Dreaded.... which cam should I get question!

    My RPM range i am looking for is 800-3500. I really don't go on the highway since it is my off-road truck. The engine in it now will be pulled out. The "new" engine has about 65k on it and had no issues when pulled supposedly. It was open and I looked it over and it looked really clean. I have...
  17. B

    Dreaded.... which cam should I get question!

    Hi Rich thanks for the info!
  18. B

    Dreaded.... which cam should I get question!

    Thanks! I will take a look
  19. B

    Dreaded.... which cam should I get question!

    Ya I know the heads suck, I could swap over my other heads which are 882's I believe, but probably not worth it. Trying not to spend a lot of money on the truck at the moment. I know I should probably just do it right the first time..... any thoughts on a cam though?
  20. B

    Dreaded.... which cam should I get question!

    Hi I just joined i am still trying to research and learn about cams, so bear with me. I know this question is probably asked all the time, but here it goes.... I have a 1976 K20 with 6" lift 37" swamper Iroks. It has a 350/ th350/ np203 and 4.10 gears. The head gasket in my current motor is...
View older results

Latest posts

Forum statistics

Threads
44,166
Posts
950,716
Members
36,282
Latest member
Doug Hampton
Top