Search results

  1. Jwernatl

    1987 Chevrolet 350 tbi high idle

    Seriously? Omg. Crazy. I love this place.
  2. Jwernatl

    Brown/black advanced wire

    Thanks - this manual is gold. Engine wise (specific to the sensors) my truck is extremely stock. I did replace the gauges, which I believe, I need to call the gauge ‘customer support line’ concerning the TCC / speed sensor set up. Best part, all procedures are laid out perfectly. Thanks again
  3. Jwernatl

    Brown/black advanced wire

    Hey All - hope all are happy. When I set my base timing: truck is off - and at full running temp 185 to 190• I unplug advance wire - start truck - set timing and idle is great - Shut truck off- Connect advance brown/black wire- Start truck - idle goes to 1000 or 1100 - Idle is higher -...
  4. Jwernatl

    New leaf springs!

    My truck is 100% stock. Sorry it took so long answering. Ive been out for a while sick.
  5. Jwernatl

    Just fyi - I dyed my carpet - it came out great

    No I simply cleaned it with green cleaner.
  6. Jwernatl

    need help w/scan tool reading volts open circuit stuff...

    and yes - I realize I'm an idiot.
  7. Jwernatl

    need help w/scan tool reading volts open circuit stuff...

    Guys - Im pretty ignorant when it comes to auto voltage. Im attaching what the manual says below….. I need to see if CKT 419 is open - Scan tool? I need to test the TPS and the O2 sensor volatage. (mainly the TPS) And, I realize this is a rookie question -** How do I test the wires when...
  8. Jwernatl

    Poll -Would doing a LS swap in a CLEAN 1987 V10 INCREASE to DECREASE VALUE?

    yea - thats it. I like originality. more so than not. Shorty81 said it best - want an ls - buy a truck with an ls - I bought this one because it's pure. - what am I thinking. You guys rock
  9. Jwernatl

    Poll -Would doing a LS swap in a CLEAN 1987 V10 INCREASE to DECREASE VALUE?

    That's what Im doing. I needed realizim. I decided - to take heads off - machine shop for complete job - valves etc - and put 'm back on. If bottom is bad when I take heads off - I'll yank it out and take it up to a certain machine shop in Lynchburg Va - have them build it right - and go with...
  10. Jwernatl

    Poll -Would doing a LS swap in a CLEAN 1987 V10 INCREASE to DECREASE VALUE?

    Thats what im leaning towards this morning - i want to finish the interior - wet sand and clear it. Drive it.
  11. Jwernatl

    Poll -Would doing a LS swap in a CLEAN 1987 V10 INCREASE to DECREASE VALUE?

    Yes - I see that. Im so on the fence. May just put a little into the heads and go with back with all new sensors - i do like its all original. Especially when its clean likw now ...
  12. Jwernatl

    Poll -Would doing a LS swap in a CLEAN 1987 V10 INCREASE to DECREASE VALUE?

    My '87 is clean -Im currently doing a restoration on it - interior, rubber, door treatments etc etc… I'm needing to re-do heads - and it's got a160k miles on it. and truth be known, it seems a little tired too…. I don't want to redo heads and in near future have issue with bottom end. So...
  13. Jwernatl

    LS swap cost - COMPLETE a-z Drive in, drop it off & pick up tuned and perfect.?

    $10k I can do that. You guys think it would devalue a 'stock' clean V10?
  14. Jwernatl

    LS swap cost - COMPLETE a-z Drive in, drop it off & pick up tuned and perfect.?

    Me too….
  15. Jwernatl

    LS swap cost - COMPLETE a-z Drive in, drop it off & pick up tuned and perfect.?

    Yes, this is still under consideration - But, I think I would like the reliability and power ease. I can't find anyone local that is able to do this.
  16. Jwernatl

    LS swap cost - COMPLETE a-z Drive in, drop it off & pick up tuned and perfect.?

    Guys - I know this is loaded question - BUT - in your opinion, what is a fair cost range to have a reputable shop perform a COMPLETE LS SWAP into my 1987 V10? Keeping my 700R4?? or swap that too? Let's say…the donor engine has less than 50k miles, perfect running engine - no need for a...
  17. Jwernatl

    Dash Alignment

    Mine was same - my aftermarket I ordered was not the best - I hate it. I used the right screws and clips. It's just not the same. Nobody knows it except me.
  18. Jwernatl

    New to tbi, no start 87 blazer

    you have fuel going in? - but it only starts with starter fluid? If you start it with starter fluid and it runs for a few seconds, can you still see the fuel in the TBI? It should be fine mist out of both injectors.
  19. Jwernatl

    'Puff' on start up! valve seals need replacing....

    Hey guys - the smoke is getting worse - Im sure the heads will need to come off — question - my truck runs good - its got 161k miles - thing is...I'd hate to pull heads off - AND after I do that - sooner than later - get a knock - loose compression - oil pressure - bearing etc etc etc -...
  20. Jwernatl

    Gauge/idle Fuse

    Here's a wire diagram for the '86 — it under the reference library. I found it a few months ago - unbelievable information - especially the ones for my '87 - it's all there - crazy good info… 1986 GM CK Light Truck Wiring Manual...
  21. Jwernatl

    Bed liner yes or no

    I've got RUBBER mat in mine - I love it.
  22. Jwernatl

    Anyone know trick to install a new (used) door spring?

    I looked for 2 days - I did - I searched - Im telling I did. But, more than anything - thank you for finding that. Im going to try it this afternoon.
  23. Jwernatl

    ALDL connector not powering scan tool

    This is right up my alley! Ill order the tool. And download the program on a tablet that I have. Ok for me to contact you for advice?
  24. Jwernatl

    'Puff' on start up! valve seals need replacing....

    Dang good stuff! And btw, its getting worse. Now its when it sits 4hrs. Or more.
  25. Jwernatl

    ALDL connector not powering scan tool

    It worked. Swapped a new coolant temp sensor - cleared ecm - and mam o man. That exhaust smelled so much better! Thank you to all you smart sombeaches. You guys make me a better man!

Latest posts

Forum statistics

Threads
44,164
Posts
950,708
Members
36,278
Latest member
kodyg86
Top