Search results
-
1974 dodge dart, unidentified component, need help ID
Seat belt interlock- fast 99
- Post #2
- Forum: Other Vehicles
-
Broken wire
That is fusible link wire. Needs to be replaced with same gauge.- fast 99
- Post #2
- Forum: Electrical & Audio
-
Loss of power and shaking
Sounds like RPM related such as broken valve train part or ignition crossfire, bad coil, ect. Drive with a gauge hooked up to manifold vacuum. Use a long hose under rear of partially shut hood. Clamp gauge under a wiper. Go around the block. If vacuum is steady that will eliminate many...- fast 99
- Post #3
- Forum: Engine & Performance
-
Biggest jobs you have completed in the shortest amount of time.
A week or 2 afterward went to Tri cities for a tow back to Spokane. Tri cities was closer to ground zero. They got 4-6 inches there, here about 2. The county had furrowed the ash into the center of the streets. Was 2' high. Never though it would be possible to ever get rid of the stuff. Took a... -
Wheel almost fell off while driving…help
How many threads are/were engaged? Thicker center on that style wheel. Spacers?- fast 99
- Post #10
- Forum: Wheels and Tires
-
Wheel almost fell off while driving…help
Unless overloaded or abused properly torqued lug nuts do not fall off. That said, GM used hub centric wheels from the factory. Many aftermarket wheels are designed to fit other brands with larger centers. Thus, they are not hub centric on GM. Just something to think about.- fast 99
- Post #4
- Forum: Wheels and Tires
-
Gas out of top of Rochester Carb
Doubtful, spring filter then nut. Why do you ask? Previous posts contain correct instructions. Was the float replaced? Fiber floats get heavy with age. Should never be reused. That's one of the Q-jet negatives. Some may disagree, brass floats are available, my experience they don't float the...- fast 99
- Post #5
- Forum: Carb Fuel Systems
-
Truck Size
Whatever the reason it's not me. So they develop an engine that works at higher RPM,s then to get millage add cancelling cylinders that causes all sorts of problems.- fast 99
- Post #25
- Forum: Other Vehicles
-
Idle Mixture Screws Do Not Adjust Anything on 1974 454.
That's news to me didn't know that was copied. I don't like much of the new or reproduction parts out there. If you can rebuild/repair OEM stuff your better off. Just today bought an emergency brake cable from a national parts chain. Spent the next 1/2 hour trying to get it to fit. Seems none...- fast 99
- Post #22
- Forum: Carb Fuel Systems
-
Biggest jobs you have completed in the shortest amount of time.
One of our tow trucks broke a crank in the parking lot when I started it up in the morning. Was a 73 K20 350 4 spd only had PS. Needed to do a jump start about 6 blocks away. Idled the truck down and back to take care of that call. Then yanked the motor out rolled it over on another pickup... -
Idle Mixture Screws Do Not Adjust Anything on 1974 454.
Can try dribbling fuel in each side of primary venturis when running. If engine slows down rich, speeds up or smooths out lean. That can also tell you if it's isolated to one side or both.- fast 99
- Post #17
- Forum: Carb Fuel Systems
-
AC Clutch Cycling Switch
AC switches are listed under switches not AC on Rock auto. If it's an original 76 system believe they had thermal limiters and bulbs.- fast 99
- Post #3
- Forum: Tech Discussion
-
Ford Trash Talk Thread lol
Sooner or later, they will all break. Although I have to wonder about that one. Flat beds or tow trucks mostly loaded the opposite way, front end light. We had several GM trucks that needed frame repair. One of my SB frame was replaced entirely. Was cracked in several places and bent from use...- fast 99
- Post #567
- Forum: Other Vehicles
-
Really weird air conditioning problem
Can you get a gauge set for both high and low side pressures? 100 psi assume low side? If that's the case something is restricting flow. Likely orifice tube. Not a good idea to clean it. They are inexpensive. Is it correct for 134a? Agree with previous poster on oil. Some compressors are...- fast 99
- Post #4
- Forum: Tech Discussion
-
Quadrajet Air Fuel Ratio
Never said they adjust idle mixture.- fast 99
- Post #10
- Forum: Engine & Performance
-
This is a coolant leak right?
Interesting, do you suppose part of that could be from numerous electrons passing to and from nearly every part of later vehicles that have OEM installed aluminum rads? Just a thought. Haven't seen to many rotted out cores. More often tanks either denature from excessive heat [low coolant] or...- fast 99
- Post #7
- Forum: Engine & Performance
-
This is a coolant leak right?
Other than an originality standpoint why do you dislike aluminum rads? From what I have seen they transfer heat much better. There used to be around 10 radiator shops in this area. Now were down to 1. Getting radiators fixed and sourcing cores isn't cheap or fast. OP, appears it may be...- fast 99
- Post #4
- Forum: Engine & Performance
-
Quadrajet Air Fuel Ratio
Yes, [alternate option] if lean a thin piece wire under the rod holder to raise the rods. Be sure the secondary spring is wound up the correct amount. Probably in the area or 3/4 - 7/8 turn on adjuster. Should be on the spec sheet that came in the kit.- fast 99
- Post #5
- Forum: Engine & Performance
-
Quadrajet Air Fuel Ratio
If the carb is an 83 there is a small plug on top that will allow access to metering rod adjustment screw. I usually take those out when rebuilding then reinstall after carb is set up. If carb is together using a small [1/8th inch] drill into it far enough to get a sheet metal screw started them...- fast 99
- Post #2
- Forum: Engine & Performance
-
Working AC again
Later 134 vehicles have insulation over the drier too. Got it from the local P&P seemed to help when at lower RPM's sitting in traffic. -
Decided on a 350 engine, still deciding on stroking it out or not.
Need to figure what is usable then decide depending on funds and skill level. If you want to stick with a carb putting a leg in it isn't a bad idea. Stroker kits are available. Heads may be modified to an extent they may be undesirable for street use. May need all new valves, springs, and...- fast 99
- Post #3
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Rough Idle and Stalling
When throttle is closed vacuum should increase not decrease. Know you preformed dynamic compression but how accurate was it? Have you checked for an intake gasket leaking underneath? Try dribbling fuel in each primary side of the carb when running any change?- fast 99
- Post #6
- Forum: Engine & Performance
-
17-in rims
Yeah that's what we figured out. Those Alcoa wheels had a larger center that fit other brands. Should have realized what was going on after the first fail. In addition the inside wheels were stock steel. Aluminum wheels flex more increasing the side load.- fast 99
- Post #6
- Forum: Wheels and Tires
-
My thoughts on spare alternators
Kind of do that. Some SB came from the factory with 2 batteries, parts are available. I installed a second one in both trucks. Second one is not isolated. Was handy at the lake when my brother's boat had a dead battery. Took one of mine out. Most new cars today do not have any extra room...- fast 99
- Post #2
- Forum: Tech Discussion
-
17-in rims
That may not be true. Had a customer with a concrete cutting business [heavy for a 1 ton]. He liked shinny stuff and installed Alcoa wheels. Then the trucks started shearing off rear studs. A couple times driving in the city both wheels came off one side, trucked dropped with expected damage...- fast 99
- Post #4
- Forum: Wheels and Tires
