Search results
-
Freeze plugs into the block- how to remove?
or suitably sized channel lock pliers.- fast 99
- Post #4
- Forum: Engine & Performance
-
LMC truck gas tanks
Might also try Summit or Jegs. Shipping could get expensive.- fast 99
- Post #4
- Forum: Carb Fuel Systems
-
New carb starts then dies after 5 seconds
What is the fuel pressure? Is the choke plate closing? Vacuum leak?- fast 99
- Post #2
- Forum: Carb Fuel Systems
-
need oil fill tube gasket
Does anyone know where I could find the thick gasket on the base of an oil fill tube? This one is hard as a rock and doesn't seal well.- fast 99
- Thread
- Replies: 0
- Forum: Engine & Performance
-
Windshield rubber trim piece
tool, I use windshield cleaner as a lubricant -
Transmission cooler ideas
Some later models have a bracket mount factory cooler, possibly adapt one or at least use the mounts. Anything you buy will likely be universal. Is there a pick and pull near you?- fast 99
- Post #3
- Forum: Automatic Transmission
-
This is a coolant leak right?
Somewhere I ran across a voltage specification that would help determine if the cooling system had turned into a battery and/or the coolant additives had been depleted. Can't remember the number but think it was in the less than 1 volt area, possibly .4v. Haven't used the test in years but at...- fast 99
- Post #29
- Forum: Engine & Performance
-
What Sending units oil and water temp needed for guage cluster to work like factory in k10 454 swap I will buying all the components new thank you
Overall parts quality is horrible. You will have better luck with GM, Delphi or AC Delco but even some of their parts are offshore. I am proponent of "if it aint broke don't fix it". Only place you can go is backwards.- fast 99
- Post #7
- Forum: Tech Discussion
-
454 water pump replacement
Don't need a "HP" pump. ^^^^this^^^^- fast 99
- Post #4
- Forum: Engine & Performance
-
Auto A/C vacuum pump. lots of CFM or Less CFM whats best?? A/C tech's please help.
An acquaintance who owns a used car lot bought some cheap supposedly virgin refrigerant. Sealed in the box. He ended up replacing entire ac systems on every car that got some of it from corrosion.- fast 99
- Post #6
- Forum: Tech Discussion
-
R12 Replacement
Certainly, changing over to 134 has been done for 20 years at least. There is a lot of information on how to do it successfully. Refrigerant oil is different, seals, drier, orifice tube, replacing hoses and flushing is sometimes needed. Most of the work could be done in the backyard environment... -
Needing some help
Agree, unless a donor vehicle is available. Pictures are too dark. Don't need to see the entire engine compartment just the component you're questioning. Am guessing but appears to be an aftermarket system. Would likely be more cost effective to buy a new complete system. -
6.2 water pump pulley
If hole is not some odd size a unibit might work.- fast 99
- Post #6
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
-
R12 Replacement
Why? 134 is available in most states and still not expensive. Back of can says be careful with flammable substances but doesn't actually say what is in the can. Hard Pass -
Bad Proportioning Valve?
We ran into a lot of problems with Ford's when these first came out. Valve was not self- centering. We were able to re-center them by opening one side or the other and slowly depressing the pedal. That procedure pushed the valve across. If the brake light flashed, then went back on opened the... -
Bubba's Brake Bleeder: A Guide
Been doing this a long time. I try to simplify brake jobs and be as efficient with time as possible. First thing, suck out the old fluid in master and refill with new, proceed with repair. If hydraulic parts are being replaced let the system drain until fresh fluid is at each corner. Gravity...- fast 99
- Post #4
- Forum: Suspension, Steering & Brakes
-
Crate SBC 350 installation plan
Most times I assemble the motor as much as possible before installation. Access is much easier on the engine stand. Have never used a leveler. My engine plate has 5 holes instead or the usual 3. Using the second one back angles the rear down. Will easily bolt up. Works on everything from a small...- fast 99
- Post #5
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Timing cover seal
Damper seal or pan gasket? Damper seal can be replaced without pulling pan. If pan is pulled do yourself a favor buy a one-piece gasket.- fast 99
- Post #3
- Forum: Engine & Performance
-
Where to buy stock mechanical fuel pump that isn't trash?
Went through a couple new bad pumps. What I found was the cheaper ones did not have a return spring on top of the pump arm. The arm stuck 1/2 way down resulting in low volume. When I finally found pumps with a spring bought spares. Both are 3 line one is a Delphi other is AC. Not sure if it...- fast 99
- Post #6
- Forum: Tech Discussion
-
88 suburban 350 rebuild questions.
One thing to consider is putting a leg in it. There's no substitute for CI. Scat parts are decent even made in China. First thing would find out of the heads are usable. If not, that decision is already made. In reality if the heads need a lot of work [money] buy an aftermarket set. Wish I...- fast 99
- Post #7
- Forum: Engine & Performance
-
Repairing damage on brown truck
Yes, it's called blending. Color is applied and feathered out. Then clear coated over the entire area. There will not be a visible blend line where color and clear coat ends. Don't understand why one of the shops would want to strip entire panel unless they are afraid of lifting. Surprised an...- fast 99
- Post #6
- Forum: Paint and Body
-
Repairing damage on brown truck
Normally that could easily be repaired and blended lots of area to feather the color. Many new mix colors make matching difficult, and it could be an issue if this was painted with an old formula. Stripped, color needs to be blended into adjacent panel. Clear does not peel if the area is...- fast 99
- Post #2
- Forum: Paint and Body
-
AM/FM Radio
I used to find them at pick and pull yards. Most had problems with scratchy controls. Bought cans of spray contact cleaner and drenched the inside with it while moving the knobs. Nearly everyone one came out of it. In the last few years those radios have dried up. Keep in mind GM used the same...- fast 99
- Post #8
- Forum: Stereo & Entertainment Systems
-
Rear dually wheels
I tried 235 16's on a dually. Sidewalls would touch when loaded, very close when not. Ended up installing 215's. OEM wheels are the same with either a cab and chassis or dually pickup. Axle width changes nothing. If you look at the picture above there is no room for more offset. Another problem...- fast 99
- Post #4
- Forum: Lifted & Off-Road Systems
