Search results
-
-
Wiring Help
Hanes manuals give a fairly good diagram to follow, welcome to the group.- Tank6x2
- Post #3
- Forum: Tech Discussion
-
Brake lights not working
Just as well to Check in behind the taillights as there’s a ground that sometimes has a poor connection to the body over time and a good time for a new set of bulbs- Tank6x2
- Post #9
- Forum: Electrical & Audio
-
Newbie Alert
Welcome from the great white north eh! congratulations on purtty ride it’ll look good no matter what you choose to do to her!:gm:- Tank6x2
- Post #17
- Forum: Introduction
-
-
Finally pulled the trigger. My C10 Project
Nice project truck you’ve got started bubba! How goes the rebuild to date!?- Tank6x2
- Post #21
- Forum: Lowered & Street Systems
-
Lowering help needed
Depends, how wide are you talking? Most likely I would lean to BellTech as they supply a fairly decent kit, I would upgrade the hardware that’s coarse thread to fine thread personally as I had a 86 wrangler that I dropped 5” total all around but I had the original 15”x10” rally rims, no issues...- Tank6x2
- Post #2
- Forum: Lowered & Street Systems
-
Love affair that started 25 years ago
Welcome from the Great White North EH!- Tank6x2
- Post #16
- Forum: Introduction
-
Water leaking into cab
Check your windshield tray below the cowling that’s there, once had a hole in my old unit rust through plugging up full of pine needles, but likely hood is slim I’d lean towards the window seal like previously suggested -
-
What have you done to your square lately??
Mounted up the rear shocks and panhard bar on Stormin Norman Tank just have to polish off the welds and clean up any of the high points on the welds to remove any chance of Notch effect to the welds. Should be a fun day! -
What have you done to your square lately??
Lately throw together my four link on the rear drop suspension on Stormin Norman Tank, looking to polish off the bags today, hopefully bring in the cab and begin dropping the top!! :Big Laugh: -
Ingersol Rand / Campell Hausfeld
Jeezus Gents! I put this out not expecting comments till new year! Thanks for all of the informatio, Greatly Appreciated!! I’ll inform myself a little and decide if I’ll need to save up!- Tank6x2
- Post #16
- Forum: Tech Discussion
-
Ingersol Rand / Campell Hausfeld
60-80 gallon compressor, oiled- who has a preference and why?- Tank6x2
- Thread
- Replies: 15
- Forum: Tech Discussion
-
What have you done to your square lately??
Been off here for awhile till recently, been working on my four link airbag setup for my 79 one ton. Had to build up around the tube a bit because the ubolts have been wearing into the parent material. -
Technical Axle Question
Radial Axis, this is true yet when you look at the axles movement is it not more a straight line that moves in a large circular motion? Maybe 90• to ride height position... But if I want them as far out as possible and directly over the axle, why is it GM that Angled them from lower centre...- Tank6x2
- Post #7
- Forum: Tech Discussion
-
Technical Axle Question
Well got another posted line of thread “Storming Norman Tank” on here in under construction, but never really gave shock load and position much thought for it until I began preparing the four link brackets this week. Could use a panhard bar to offset the torsional load, but the question now is...- Tank6x2
- Post #4
- Forum: Tech Discussion
-
Technical Axle Question
open to anybody who wants to share, is the reason the rear shock brackets are offset from front and rear sides of the axle due to torsional load or was this just a slight difference in patent design to allow the same design from Chevy Dodge Ford to be used with a minor alteration to design so it...- Tank6x2
- Thread
- Replies: 11
- Forum: Tech Discussion
-
Welding help needed.
When your not using your wire, protect it from environmental contaminants, don’t remove it from your machine, just keep it wrapped up with a garbage bag/a zip tie. Tack every inch or so, and keep the the next weld 6-8” away from the last weld 0.035/0.030” Wire should be fine for what your...- Tank6x2
- Post #26
- Forum: Tech Discussion
-
New member, tire size question after reading threads for 2 days
There are 15"x10 Rallies, I think LMC has them, if not dig around they do exist!- Tank6x2
- Post #10
- Forum: Wheels and Tires
-
Hello from the PNW
Isn't she a sweet little mule, WELCOME! Lots of good info on here these guys all put out...does it have a name yet?...Ive had a C30 in the family for 20 years now, same unit, ran through it when 15 with dad, and just tore it down again this year completely, their awesome squares!!- Tank6x2
- Post #2
- Forum: Introduction
-
New member, tire size question after reading threads for 2 days
We need pictures though! Pics pics pics!- Tank6x2
- Post #6
- Forum: Wheels and Tires
-
New member, tire size question after reading threads for 2 days
Measure your wheel well Check the rear wheel well and then check out the offset when your ordering, KAL tire would be able to help out in the retrospect, Fountain Tire too...- Tank6x2
- Post #5
- Forum: Wheels and Tires
-
New member, tire size question after reading threads for 2 days
Well... Depends on what look your going for, you want the wheel size proportional to the tire, do you want the tire to help in the lowering just a little bit more, do you want a little more rideability for going down gravel or pot holes. Tires are sized as follows, if you didn't know...- Tank6x2
- Post #2
- Forum: Wheels and Tires
-
Exterior Cleaning Products
Save your money Take it to a highway "tractor" truck wash bring a set of ramps and pay some one to steam clean it real nice, that'll be your best bet, you can spay crap on it, but you'll be forever pressure washing it off, like trying to piss on dryer shit on the inside of a toilet bowl...
