Search results

  1. MrMarty51

    Bore vs. Stroke, a little math

    I think, long as You dont throw a bunch of alphabets into the equation, I wont get all frustrated and confused. :happy160::happy175:
  2. MrMarty51

    New from the North West

    Welcome, from eastern Montana.
  3. MrMarty51

    The swap started today.....

    Before shoving that new enjun in the hole, if it were Mine, I`d be shoving a new oil pump and rear main seal in it too. Also the front transmission pump seal. Good thread, nice truck and build too.
  4. MrMarty51

    New here from Augusta GA

    That is one sweet looking truck. If You decide to keep the solid lifters and cam. I like to use a dial indicator to adjust the valve lash, much better and more accurate than a feeler gauge. Feeler gauge bridges the worn spots on the rocker arm, where the valve stem rides, dial indicator takes...
  5. MrMarty51

    Looking for some parts.

    She is kind a cute, send her over here. :happy160::happy175:
  6. MrMarty51

    88-98 Chevys, 99-02 Chevys, and 94-01 Dodges.

    The dent is just below the 4X4 decal.
  7. MrMarty51

    88-98 Chevys, 99-02 Chevys, and 94-01 Dodges.

    Come on over, I have a 91 K1500, extended cab, manual trans, needs an engine. I have put about 650 bucks into this unit, brakes, ball joints, changed fluids and new cam, lifters, push rods, rocker arms, oil pump, timing chain/sprocket set and changed all the fluids. Turned out the lifter ticking...
  8. MrMarty51

    Wires Run To Transmission Through Floor

    There is wires run to the front of the tunnel on My 78 K20. I believe it has to do with the backup lamps on the back end. On Mine there is a place for them to run through, sort of bent up wards to make clearance, appeared to be from the factory like that. In the pic. I dont see that bent up...
  9. MrMarty51

    88-98 Chevys, 99-02 Chevys, and 94-01 Dodges.

    And I wonder why a 500,000 mile enjun was put in a 50,000 mile truck ? :happy160::happy175::happy175::happy175::happy175:
  10. MrMarty51

    Introduction

    Nice truck, nice fixumup job too.
  11. MrMarty51

    Pto

    Most PTO mounted pumps puts out max at between 1200 and 1500 RPMs
  12. MrMarty51

    88 r30 500.00?

    Find a rear door off of a Suburban and drive it. CCs are very tough to come by, SB CCs are even harder to find, at least in these parts.
  13. MrMarty51

    Pto

    Nice setup Honkey Kong. I have thought about setting up an air compressor similar to that.
  14. MrMarty51

    79 Trans am

    That`ll be a fun to drive outfit. What enjun and trans are you going to use ?
  15. MrMarty51

    Pto

    Dump trucks was My main purpose when working for the Montana DOT. Not much to installing a PTO. A shift cable or lever is all thats needed for engagement, unless You get fancy and do it with air or 12 volt power solenoid. Use shims or gaskets to get the gears spacing.
  16. MrMarty51

    Oil Exploded All Over Engine Bay

    Oil pressure sending unit ? this will empty the oil real fast, within a minute. Is there an aftermarket OP gauge that is tube fed ? Other wise, clean it all up real good with some solvent or BBQ lighter fuel{same stuff} then warsh it down good with soap and water, dry it off real good, fire up...
  17. MrMarty51

    Pto

    I have a PTO unit setting in the shed. I too had thought about running a splitter with it, dont burn wood any more so no need. It would require a PTO shaft to the pump, unless a person used a coupler sleeve. I am not sure but, I think the PTO gears on the trans/T-Case are pretty much...
  18. MrMarty51

    Howdy from Colorado

    Welcome Shane, check for voltage to the HEI distributor.
  19. MrMarty51

    Truck only starts sometimes (Distributor?)

    Is it blowing black smoke out the exhaust ?
  20. MrMarty51

    Hello from NC

    Welcome to the forum FFM. As Honkey Kong stated, pics. are nice to see.
  21. MrMarty51

    Sometimes you just stare in amazement....

    :happy175::happy175::happy175::happy175:
  22. MrMarty51

    Help me ID these wire connections...

    Harmonic balancer might be slipped off mark. Best to st timing by kickback when starting, then retard until no more kick back, road test to be sure it does not ping, if so, set back timing until it just quits pinging.
  23. MrMarty51

    Interesting blower stuff

    The 2000 K3500 with the 6.5 diesel I have was having issues with the turbo, it is an electronically controlled wastegate. New vacuum pump, new boost control solenoid and it works wonderfully now. EGTs was up over 1200, I was very concerned about those numbers, found out that they will withstand...
  24. MrMarty51

    Loud clunk after dizzy install...

    My brother run a road band for many years. they were playing music in one of the bars over here, Later in the evening and after one of their breaks. I was up dancing with a girl, I pointed at the band and told Her, well, would You look at that. All the band members had their ball sacks hanging...
  25. MrMarty51

    New Guy from the Black Hills of SD

    Welcome to the forum SDJM, from your neighbor across the Montana border. Well, a short patch of Wyoming too, Miles City, Montana.

Latest posts

Forum statistics

Threads
44,163
Posts
950,661
Members
36,276
Latest member
2manysquares2care
Top