Search results

  1. MrMarty51

    4L80E Information Thread

    Then a gauge rated at about 500 PSI would be a wise choice to allow for spikes in the system ? Thank You for the response.
  2. MrMarty51

    4L80E Information Thread

    Filling a gauge pod on the dash of My 2000 K3500 that runs the 6.5 diesel and a 4L80E transmission. The post pillar pod it has the boost, EGT and transmission temp gauge already installed. The pod on the dash has a two position fuel pressure gauge and a temp gauge reading from the rear of the RH...
  3. MrMarty51

    Scores from DIY Parts Yards, Pull A Part, U Pull It etc

    I will check that this morning, bephore heading to working. I need to check the oil on that car and on the 88 Buick Century. Have not had the hood opened on the Buick phor about a munth, it most likely is about ready phor a fifth, oooops, quart, yup a quart. :)
  4. MrMarty51

    4L80E Information Thread

    The tuners said there would be no problem, but, I tend to be an overthinker and a worry wart to boot. New Stock optimizer with injectors set at 1950 PSI will produce no where near 800HP and most likely about 300 at the very too side. Thank You very much for the info.
  5. MrMarty51

    4L80E Information Thread

    I d I do know that he gad some real special torque convertor, maybe called yank, or some such. He also was hauling extremely heavy loads through some very rough mountain passes. Also running higher than stock tune and a real nice turbo charger system, but I dont know much more about what He was...
  6. MrMarty51

    4L80E Information Thread

    Installing the new AMG GEP Optimizer 6.5 diesel engine into My 2000 K3500, CC, LB truck with 4:11 gears. I made the purchase of a new ECM module that has the TCC engaged upon deceleration instead of disengaging and coasting. I have heard of horror stories of the input shaft snapping on such...
  7. MrMarty51

    Air in fuel lines after sitting over night on 6.2

    The later diesel trucks had the LP (lift pump) located on the frame rail, in about the location at the back cab door or maybe back a slight bit more. Easy to get to and to maintain (replace). Also, the integrity of the mechanical pump can be checked by hooking a FP test gauge to the outlet hose...
  8. MrMarty51

    Air in fuel lines after sitting over night on 6.2

    On top of the injector pump, short 1/4” hose shaped like an upside down U. Remove that hose and replace it with a length of 1/4” fuel rated clear plastic hose. Start the engine and watch for air intrusion. Might appear like a white foamy substance while the engine is running. If there is air...
  9. MrMarty51

    Lawn/ Garden tractors/ Riding Mowers, Cool Mods and tinkering

    Here is a lawn tractor that My dad built. What He could not find in the scrap heaps at the recyclers He fabricated and machined. The boiler was made from an oxygen bottle and the cylinder and piston He machined. He sold this when I was in the army. I now am searching for it and have got several...
  10. MrMarty51

    Straight 8 Buick With Belt Driven FI

    I didnt know that about the Buick engines. I had seen the engine in an old Buick at the shop where my dad worked. That was back in the days when I was first becoming aware of different performance options.
  11. MrMarty51

    Straight 8 Buick With Belt Driven FI

    My thoughts too, and, it did not fall over. :laff
  12. MrMarty51

    Straight 8 Buick With Belt Driven FI

  13. MrMarty51

    Straight 8 Buick With Belt Driven FI

    I believe so. Coolest sounding enjun in town.
  14. MrMarty51

    Straight 8 Buick With Belt Driven FI

    Back in the late 60s, I had a 1953 Pontiac with a flathead straight 8 and an automatic transmission. That thing would fly.
  15. MrMarty51

    Straight 8 Buick With Belt Driven FI

    I did some screen shots from a fake book page about the straight eight Buick engines. It did not say what year this engine is but IIRC, the last year for any of the GM straight eight engines was 1953 or possibly 1954.
  16. MrMarty51

    FOR SALE: 81-87 Guage Cluster GREAT-CONDITION

    I am so happy that this all got resolved in a proper manner. If anyone knows who this Arley B. Ospina is then I suggest, putting together a good old fashioned blanket party for that feller.
  17. MrMarty51

    FOR SALE: 81-87 Guage Cluster GREAT-CONDITION

    TT
  18. MrMarty51

    FOR SALE: 81-87 Guage Cluster GREAT-CONDITION

    Excellent condition, has been tested and all woks ok. Very rare to find one this nice. Just PM me if anyone wants to but it now. $250 shipped US.
  19. MrMarty51

    Choke Problems on SBC

    I hope that You are attending THOSE meetings and are working with a sponsor. Do not stalemate out on that 4th step.
  20. MrMarty51

    Choke Problems on SBC

    It is all back together. Before dismantling, brought the timing marks to 8* BTDC, marked the distributor how it all sets. Got it back together. Set the choke, Nick twists the switch to start, boom, not even one revolution and it is running. Turned on the timing light, he Nick, look at this...
  21. MrMarty51

    Choke Problems on SBC

    There is no more hot tanks in town. I would have loved to do dat to the intake maneeefold, rocker covers, bolts and etc. Yeah, hot tank is the answer for sure.
  22. MrMarty51

    Choke Problems on SBC

    He also has a 1972 K30 GMC that has a 454 planted within. A lot of rust. Before I knew about it he had pulled the flatbed off. Found a box and got it home. He proceeded into rust repair. Before long he has the cab lifted off, floor cut out, rockers, cab corners and ant thing else that needs...
  23. MrMarty51

    Choke Problems on SBC

    Got all the components scrubbed and ready to reassemble. Step son is a mighty tough task master. He dont slow down. He is a fast learner too. I hand tools to him like He has never before used, I explain their function and then get out of the way. I mostly just sort out for the next step and...
  24. MrMarty51

    Choke Problems on SBC

    I just got started hammering on the butt end of the handle of that Snap On screw driver to chisel out the carbon, then the thought, pics, I need pics to make everyone happy. And so here they are. Plugged solidly shut. Oh yes, too, snap on screw drivers are good to use for chisels too.
  25. MrMarty51

    Choke Problems on SBC

    Oh yes. Thank everyone for the replies. With this information I can now honestly and sincerely tell the stepson that the manifold must come off to get it right.

Latest posts

Forum statistics

Threads
44,163
Posts
950,661
Members
36,276
Latest member
2manysquares2care
Top