Search results

  1. V

    86 C10 with bent frame

    C10 lwb (these are from the KLM/Mitchell manuals) KLM manual on ebay at the moment
  2. V

    86 C10 with bent frame

    Here is the swb sheet
  3. V

    Hi, I’m new here

    Where are you in LA? I’m in SW MS
  4. V

    2.5" or 4" Lift 1986 K10

    I’ve had a 2.5 lift with 33s on my truck for over 20 years with no issues This is an old picture, as it is torn partially apart now, but should give you an idea
  5. V

    0411 pcm labels? how to order the correct one without using a vin number?

    I’ve got a 5.7/4L80 pcm I think I can send you the stock .bin file. You can download Universal Patcher and load it to any 0411 The reason I say think is, I have it on my laptop and believe I can send it as an attachment, but have never tried
  6. V

    Engine Identification?

    The 400 block is the only factory small block block with 3 freeze plugs per side (later 400 blocks only have 2 but the “boss” for the 3rd is cast into the block). Also the factory 400 harmonic balancer has a “notch” roughly 1/2 the way around it, from being externally balanced. Later 400...
  7. V

    SWAPPING 84 c10 body onto 84 k10 FRAME

    81-83 4wds (not sure on manual trans 2wd) also had a bolt in hump, but the floor was shaped different than the 73-80, 84-up 4wd pickups had a one piece floor. I parted out an 89 Blazer a while back that had the bolt in style hump, but was spot welded to the floor from the factory. Here is the...
  8. V

    Hydro Clutch Pedal Assembly...from an S10?

    PM sent Yes I realize that. I’ve never had a daily driver with an automatic in 40 plus years of driving, having 3/4 & 1 tons, usually with aftermarket clutches, which were stiffer even with hydraulics. Plus, my left knee needs replaced. Sold my last gooseneck trailer a while back, so plan to...
  9. V

    Hydro Clutch Pedal Assembly...from an S10?

    Wow, for a few hundred less than what Level 7 wants, i’d sell the whole setup I plan to pull out of my truck, to include the pedals, bell, 4 speed trans, clutch, and tilt standard trans column.
  10. V

    Quad Shocks

    When GM put quad shocks on the trucks, they cut the valving/stiffness of the shocks in half. I have not found a set of aftermarket shocks valved this way. Idea was, as I was told by an old GM parts man, there was twice the oil to heat up when offroading
  11. V

    My parts truck has auto hubs on the Dana 60!

    I have a set of NOS Dana 60 auto hubs (one has a Ford cover, unfortunately)
  12. V

    NP208 Tcase housing wanted

    Think I have a spare front half. Let me look this afternoon.
  13. V

    opinions on my LS swap setup

    I’ve got a 2000 Tahoe 5.3/4L60 that is factory drive by wire. DBW was included in the RPO NW7 Traction Control system.
  14. V

    Issues with being stood for a long time?

    My 84 sat for 9 years without being cranked. I put 2 batteries in it and drove it home. Didn’t take long for me to get the old 6.2 going.
  15. V

    Are locking hubs factory or personal add on?

    They even made auto hubs for the Dana 60 after 81. Here is a NOS set I have (one has a Ford cover, but other than that, they are the same) And from the 1981 pickup brochure
  16. V

    Are locking hubs factory or personal add on?

    Main thing about automatic hubs is, don’t put too much grease in them, just need a small amount. I think overgreasing them is the reason they got such a bad name.
  17. V

    Theoretical Big Block Build

    On that era of 454, we always added closed chamber heads to get better performance. The flat top pistons that era combined with the open chamber 117-119cc heads (781/290/236 aka peanut port) produces a true compression ratio of about 7.7-7.9:1
  18. V

    Theoretical Big Block Build

    236 casting heads flow about 230cfm and will support about 550-600hp with very minor port work. We’ve had several sets on a buddy’s flow bench, and used them in local class races. I’d be more worried about the tbi flow, even with the 7.4 tbi having a higher cfm flow rating than the small...
  19. V

    Exhaust pipe bracket

    Are you needing the driver’s side or passenger’s side brackets? I may still have a set from a factory dual exhaust pickup
  20. V

    12 Valve swap

    Depends on if its going in a 2wd or 4wd. And it’s intended usage. Running stock? Or intending to increase power? I’ve done a few Cummins conversions, but everyone seems to have their own idea of what is the best way to do it
  21. V

    K20 vs. K30 Difference

    Another thing to remember is that the k30 frame has the shock mounted inside the frame instead of outside.
  22. V

    What’s IT Worth? (Post all “what’s it worth threads here)

    Going to swap my 85 k1500 to automatic. Anyone got a rough idea of what an 85 tilt standard column, 85-up hydraulic clutch pedals for hydroboost, with all hydraulics, 465/208 combo is worth? Also have the 6.2 flywheel and clutch setup. I believe the only thing missing is the bellhousing dust...
  23. V

    I just bought a John Deere tractor!

    Good tractors. Don’t get in a hurry with it, as they are low power, but dependable. Its a great garden tractor
  24. V

    New here from Mississippi

    Well, I won’t ruin that for you, and will just say there was a LOT of human “error” involved. Girl I went to school with was one of the big organizers for the monument. It’s close (1/4-1/2 mile) from the actual crash site, but its a swampy area. Liberty is also known for Jerry Clower. Know...
  25. V

    New here from Mississippi

    Last year was the first time I had ever went to the monument. Know several that helped the night/morning after the crash. My sister still has tickets to the concert they were flying to Baton Rouge to perform.

Latest posts

Forum statistics

Threads
44,162
Posts
950,643
Members
36,276
Latest member
2manysquares2care
Top