Search results

  1. V

    NEW Brothers Dash Bezels - CHEAP

    I went thru the “sellers other items” and bought this for my 87 R10. Should be here Monday https://www.ebay.com/itm/286061686749?epid=23061992116&itmmeta=01JCTVJ32K0FK5X03PJGGYQ8PK&hash=item429a9aefdd:g:~MkAAOSwmupm5qk6
  2. V

    A small section of bed floor

    Will try to remember to look in the morning, (have a funeral and Vet Day service before the night shift) but may still have some sections I saved.
  3. V

    What will cause this to happen in a 208 Transfer Case (Pic Inside)

    Make sure your speedo cable isn’t binding, lube it. I’ve been able to pull the center out of some and smear grease on it and reinstall, make sure it turns easily. Check the driven gear as mentioned. You should be able to turn that drive gear around and reuse, as it doesn’t look bad. The drive...
  4. V

    Check out my rear end

    Looks to be a normal 1970s Eaton GM 12 bolt truck posi carrier. I’ve owned several, may even still have one or two.
  5. V

    Truckin' the Trace November 1 - 2, Tupelo, MS

    Of course, as I’ll be around Tupelo THIS weekend, and will be at work nest weekend.
  6. V

    Dynamic compression

    What is your static cr?
  7. V

    Best Locker for 14Bolt FF in 85 K30

    The Gov Loc for 14b ff is not a bad unit. Like someone mentioned above, I did not care for either the Lock Right or Detriot Locker’s manners on the street. So much so, I replaced with a new Gov Loc unit. The money I had trying the 2 others was the same as the new Gov Loc from Eaton
  8. V

    Cruisin the Coast 2024

    We had a good time Friday. Too much to even attempt to see in just one day. Spent most of it in Ocean Springs. Left OS close to dark and went to BSL. Did run into some people we know in Biloxi. They had their General Lee, Roscoe’s police car, Boss Hogg’s convertible, and Daisy’s Jeep with them.
  9. V

    Cruisin the Coast 2024

    Going to spend time with my 93 year old uncle. He lives in the Villa Maria apartments (the 13 story building in OS) so we’ll walk around there, but it’s mostly up to the wife and daughters. May run 90 down to BSL to get a picture of my daughters with the Publius Pray historical marker (my 4th...
  10. V

    Cruisin the Coast 2024

    We are riding down to Ocean Springs tomorrow, but have to be back tomorrow night.
  11. V

    Cab swapping.

    Be careful when welding on the 84-up cab floors as I believe 84 was the first year of galvanizing on the floors.
  12. V

    12v Swap Into 87 C30

    It’s said and done now, but with a little work, could have got everything tucked in without needing a body lift. If you want to run a mechanical fan, swap out your second gen fan hub for a 1st gen one. It should give you and extra inch or so of clearance. Get the fan to match the one you get as...
  13. V

    New here from ponchatoula,La

    Welcome from just over the state line in Liberty, MS
  14. V

    Transfer case identification

    Looks to be an 1983 manufactured 208 C by the tag, which if your truck is an 81-87 1/2 or 3/4 ton should be the right case. Only differences would be large or small input shaft, depending on transmission.
  15. V

    Engine Crossmember Replacement

    A good front crossmember down here is sw MS is a $100 - $150 part. Wonder what a bare crossmember weights? Shipping would probably be costly.
  16. V

    Let’s see your memorabilia?!

    It is of that series. I think it’s a 4100, but would have to look. The manual says it for the “3000, 4000, 4100 & 7100 series” Word has already gotten out though, as I’ve had several asking if I’ll turn drums and rotors, as no one does that, that we know of, in about a 50 mile radius from where...
  17. V

    Let’s see your memorabilia?!

    Not sure it’s memorabilia, but picked these up a while back. If I can ever finish my shop, they will have a good home. Got all the adapters, manuals etc also. Brake lathe Alt/starter tester from a closed down Napa
  18. V

    Rust removal

    You can also de-rust using an electrolysis setup. One of mine is just a 5 gal bucket. Water, washing soda, wire, some iron and an old battery charger. I Put 4 pieces of rebar around it on the inside, Connected together with copper wire. Fill with water, stir in some washing soda, submerge...
  19. V

    LT1 Swap Vendorss?

    The harness is pretty simple to do, as you are removing wires not needed. Brenden shows what can be removed at his link, https://lt1swap.com/lt1_pcm_pinout.htm He can also program the ecm. If you are not modifiying the engine, the black box ECM is fine. it’s very simple to make standalone...
  20. V

    LT1 Swap Vendorss?

    .
  21. V

    Any black two tone trucks out there?

    I’m considering painting my crew cab square black and charcoal gray two tone
  22. V

    Year ID - Headlight Bezel

    The quad headlamps was available in 1981 as part of the deluxe front appearance package. My 81 Silverado had quad headlights. They are even shown on the 81 brochure
  23. V

    86 C10 with bent frame

    C20 lwb
  24. V

    86 C10 with bent frame

    4wd Blazer
  25. V

    86 C10 with bent frame

    K10 swb

Latest posts

Forum statistics

Threads
44,163
Posts
950,654
Members
36,276
Latest member
2manysquares2care
Top