Search results
-
What have you done to your square lately??
Thanks, I'll check that out. -
What have you done to your square lately??
Put a new fuel filter on the CUCV (again, just replaced it a few weeks ago), it was leaking, so thought I got a bad one. It looked fine, but swapped it anyways. Now the damm thing is leaking worse :( I'm guessing there is something wrong with the housing, its dripping between the housing and... -
Seat brackets..
If you just need brackets, I have some on a trashed out 78 seat that is going to the landfill in the next day or so. Let me know ASAP and I will pull them off for you. -
New to the site…
Welcome from Rapid City. Now I know why I can't find any deals on squares around here, you've bought them all!- SDJunkMan
- Post #18
- Forum: Introduction
-
What new tools have you got lately?
There were a half dozen dies at an auction here a while back, I wanted a couple of them but they sold as a group for more than I was willing to pay. My bender is a #2, not sure of the pin size, would have to check. -
What new tools have you got lately?
Yeah, but they are proud of them. I suppose I may have to break down and get some one day. I bought the bender years ago when I was raceing, but had freinds that I could borrow dies from if needed. Unfortunately they or their benders are long gone. Some day when I get caught up on my other... -
What new tools have you got lately?
Nice, I've always wanter a shrinker/stretcher. -
I don't know where else to post this so...
It just means 50 posts period, many folks welcome the new members and respond to several posts to get their count up to 50 right away.- SDJunkMan
- Post #20
- Forum: Introduction
-
New to forum
Welcome from South Dakota. Great looking stepper, I'm working on one myself.- SDJunkMan
- Post #3
- Forum: Introduction
-
Windshield question
Should be the same, I think all squarebodys use the same glass, 73-74 might not have the antenna in the windshield.- SDJunkMan
- Post #2
- Forum: Tech Discussion
-
New to the Forum
Welcome from a fellow Rapid Citian! Nice truck, don't think I have seen it around yet.- SDJunkMan
- Post #8
- Forum: Introduction
-
Part Identification Flywheel Filler Plate
Not sure of the name either, Just a dust shield, but I think they are specific to ths transmission. Like Snoots says, some were metal.- SDJunkMan
- Post #5
- Forum: Engine & Performance
-
What have you done to your square lately??
Thanks, I'll check that. Supposed to snow again tomorrow so I need to get it fixed asap. -
What have you done to your square lately??
Changed the fuel filter on the CUCV a couple of weeks ago (the rectangular one on the firewall). Worked great for a few days, but after the Sub zero cold snap a couple of weeks ago it started to leak, dripping a little when running. I wiggled it to make sure it was seated ok and the leak... -
Transfer case support rod
Here’s what I have, not sure what transfer case it is but hopefully you can tell if it will work.- SDJunkMan
- Post #16
- Forum: Transmission & Transfer Case
-
Transfer case support rod
Sorry. I'll look today, it's been down below zero all week so I haven't been to my shop. Supposed to hit 40 degrees today (heat wave). I am 99% sure I have one just not sure if its the right one.- SDJunkMan
- Post #12
- Forum: Transmission & Transfer Case
-
Transfer case support rod
I might have one, It’s from a 76 or 77 with a 350, but not sure which transfer case. I’m out of town right now but can check this weekend when I get home.- SDJunkMan
- Post #4
- Forum: Transmission & Transfer Case
-
1983 K5 Blazer manual rear/tailgate window handle just spins? How do you take it apart!?
Depending on your trim level, you may or may not have the plastic/carpet panel. The crank mechanism is prone to breaking, and from what I've read, the replacement ones are crap. You said the window is down, so that is good, you can open the gate to work on it. If I remember right I had to...- SDJunkMan
- Post #3
- Forum: Tech Discussion
-
Rosie
Welcome from South Dakota. Looks like a nice truck to start with.- SDJunkMan
- Post #3
- Forum: Introduction
-
Newby
Welcome from South Dakota. Short beds and stepsides are both getting hard to find, but there's still a lot of squarebodies out there.- SDJunkMan
- Post #2
- Forum: Introduction
-
Steering box frame reinforcement Idea?
I wouldn't think the truss would be too hard to make if the plate works.- SDJunkMan
- Post #5
- Forum: Lifted & Off-Road Systems
-
Steering box frame reinforcement Idea?
I'm getting ready to scrap what's left of a burb frame and was wondering if anyone has tried making a frame reinforcement plate out of another frame. It looks like the plate they sell is just a plate stamped to match the frame being reinforced. I would think that a piece cut out of the same...- SDJunkMan
- Thread
- Replies: 5
- Forum: Lifted & Off-Road Systems
-
What new tools have you got lately?
Also picked up a new top box, although I have no idea where I am going to put it. My son was at Lowes and saw it marked down and called me. He got 2 of them (one for each of us) for $61 each! Regularly over $400. New and undamaged, we figured they changed them a little, so marked down the... -
What new tools have you got lately?
Picked up a HF soda blaster and almost full 50lb bag of soda for $40 off Craigslist. They also threw in a new packnog nozzles and a nice pair of goggles. Only been used a couple of times. Not sure how useful it will be cleaning up the cab when I rebuild my 78, but figured it would be better...
