Search results
-
78 k10 starter problem
have you checked for missing teeth on the flywheel?- DanMcG
- Post #2
- Forum: Tech Discussion
-
How do I open hood?
wow, I guess you don't have to worry about that puppy rusting! LOL- DanMcG
- Post #18
- Forum: Paint and Body
-
Current Market On A 1982 C10 Regular Cab Short Box W Dual Tanks
My 2 cents is just pay what you think its worth don't look to steal it. under 3k isn't terrible. Yes they made a shitton of them, but try to find one.- DanMcG
- Post #31
- Forum: Introduction
-
Current Market On A 1982 C10 Regular Cab Short Box W Dual Tanks
I see it's listed under your avatar, did you buy it?- DanMcG
- Post #29
- Forum: Introduction
-
What’s IT Worth? (Post all “what’s it worth threads here)
Thanks guys, that's about what I thought the market would bare, It's a Chevy grill. -
What’s IT Worth? (Post all “what’s it worth threads here)
What's a fair value for an average unbroken but faded 73-74 grill? has a 350 emblem too. -
Firewall Rust
Yes that's it. Put a hose in the cowl and watch it pour out the drain behind the fender. also check the floor for wet spots- DanMcG
- Post #10
- Forum: Paint and Body
-
Aftermarket doors
I think I'd need to see pic's of what you're talking about, but as far as I know they only made one door for the pickup, suburban or blazer. even the mid size trucks used the same door. -
new tool for wire
I beleive that is for measuring sheet metal.- DanMcG
- Post #2
- Forum: Electrical & Audio
-
Anyone Ever replace a Firewall Insulation Pad ??
What did you use for this? or can you give me a brand to research? -
New seat bottom foam vs re-building existing?
I can't answer what the new foam is like, but I just wanted to mention a lot of times a soft sinking seat is due to broken springs and other seat frame items. -
corvette side pipes on 87 step side
how about a pic of the pipes?- DanMcG
- Post #15
- Forum: Retro-Fit & Aftermarket Accessories
-
corvette side pipes on 87 step side
side pipes would look good to me, I wouldn't care much for stacks. And yes, I got nothing to offer to your how to questions. But I'm looking forward to what you end up with,- DanMcG
- Post #2
- Forum: Retro-Fit & Aftermarket Accessories
-
-
-
Water getting in
I thought I'd follow up on this thread. As I mentioned above my windshield gasket was leaking and I temporarily fixed it but I'd still find some water on the floor from time to time. I finally figured out that the door to cab seal was so flattened out that the water was running down the door gap...- DanMcG
- Post #14
- Forum: Paint and Body
-
COWL HOOD MOLDING
This could also be an option for some that just want the look. https://www.amazon.com/dp/B08PDT6XCB/ https://www.amazon.com/dp/B08XHQVF61/- DanMcG
- Post #25
- Forum: Aftermarket Accessories
-
COWL HOOD MOLDING
as a temporary fix could you wrap you warn out one with some chrome vinyl wrap?- DanMcG
- Post #22
- Forum: Aftermarket Accessories
-
-
Is This a 74 Dash?
Well I never hooked up with the owner so when back and looked at this thing again. It sure looks like a 84 cab. couldn't find a vin on the frame rails, which didn't surprise me and never thought to bring something to scrape off the flat on the block to check numbers. I left him a message that if... -
-
Desperately look for this trim piece
if it's metal it can be polished and sealed. People have been looking for these forever. -
NECESSARY Q-jet vacuum lines needed
Can you post a pic of the carb?- DanMcG
- Post #2
- Forum: Engine & Performance
-
Is This a 74 Dash?
Is there a partial vin on the engine block, if so where abouts... behind the distributor? -
Is This a 74 Dash?
I forgot about the blue tag, I'll have to look tomorrow when I go back. the oddity about this truck is the vin tag on the B pillar is removed, and still has the holes where it was, and it's still titled and registered as a 74. all along with a 84 vin tag in the dash window. So why change out the...
