Search results

  1. highdesertrange

    Truck is walking while driving

    you said it has a 4" lift. does it have a raised steering arm? if it doesn't the frame is cracked. highdesertranger
  2. highdesertrange

    Add 2" to the front end of an existing Lift

    the reason I said they are 2 inch is the angle of the drag link. it appears there is not a raised steering arm installed, and the offset appears to be minimal. highdesertranger
  3. highdesertrange

    Here is a weird one for you...

    thank you Justin. the end result is always better and usually cheaper if you follow proper troubleshooting. highdesertranger
  4. highdesertrange

    Sloppy Window Crank Handle?

    I am just telling you what the foam is for. if you want to make it into something it's not, to take up slop that's your business. if it were me I would fix the problem and not mickey mouse it. highdesertranger
  5. highdesertrange

    Turn signal lever

    yep better not yank on it. there is a screw holding it in place. highdesertranger
  6. highdesertrange

    Sloppy Window Crank Handle?

    that foam piece is meant to stop drafts, not to make the handle tighter. if your handle is sloppy it's probably worn out or it's a cheap Chinese replacement. highdesertranger
  7. highdesertrange

    Ignition switch vs ignition lock

    adjust the switch. the new switch should have come with adjustment instructions or get them from a manual. highdesertranger
  8. highdesertrange

    Whats all needed for a 4 inch lift?

    do not drive it without the steering arm. highdesertranger
  9. highdesertrange

    Here is a weird one for you...

    instead of just buying parts and hoping that's the problem. why don't you find the trouble shooter flow chart, find out the real problem and fix it. highdesertranger
  10. highdesertrange

    Add 2" to the front end of an existing Lift

    ok it looks like 2 inch front springs. if they are, just install 4 inch springs make sure you install a steering arm too. highdesertranger
  11. highdesertrange

    4x4 shift knob

    there is a jamb nut under the shifter. back that off first then it just unscrews by hand. highdesertranger
  12. highdesertrange

    6" lift leveling

    first off how was the rear lifted? block/add-a-leaf combo, springs only, springs and blocks combo, shackle flip? highdesertranger
  13. highdesertrange

    Add 2" to the front end of an existing Lift

    for me to make a recommendation over one pic is hard. let me ask this can you post some better pics? does it have a raised steering arm? the reason I ask about the steering arm is the angle of the arm is what led me to believe the springs were shot. highdesertranger
  14. highdesertrange

    starter heat shield...aluminum or blanket?

    install a hot start on it. highdesertranger
  15. highdesertrange

    Any square body recyclers/wreckers?

    I just made my own grill and put a bow tie off of a 67-72. highdesertranger
  16. highdesertrange

    Add 2" to the front end of an existing Lift

    it appears the arch has gone out of those springs. either that or they are only 2" lift springs. highdesertranger
  17. highdesertrange

    Change from 2:73 to 3:73

    it's not the housing you have to worry about. it's the carrier. that's probably a 10 bolt in your truck. I am just guessing but I would say yes you will have to change the carrier. I personally wouldn't put that kind of money in a 10 bolt. now maybe you could find a used one and swap them...
  18. highdesertrange

    Add 2" to the front end of an existing Lift

    got pics? how was the front and rear lifted? highdesertranger
  19. highdesertrange

    SM465 getting hot?

    how hot is hot? if the fluid is getting hot you have a bearing going out. which is likely if you were a quart low. highdesertranger
  20. highdesertrange

    Fuel cell plumbing

    then it's not a fuel cell, it's simply a fuel tank. highdesertranger
  21. highdesertrange

    Fuel Sender question

    so put a sending unit in from a mechanical pump gasser. you still have the wrong sock. highdesertranger
  22. highdesertrange

    Fuel Sender question

    you realize the socks are different for gas. if you put a diesel sending unit in you would then need to change the sock. next question why didn't you just put a gasser sending unit in? highdesertranger
  23. highdesertrange

    Fuel Sender question

    my question would be, why put an after market gauge in. the diesel sending units would still work with gas just change the sock. seems like a lot of trouble for a 10 buck part. highdesertranger
  24. highdesertrange

    What is the oil pressure supposed to be?

    before replacing an engine I would verify the oil pressure. do this with a good mechanical gauge. do not trust electronic gauges. highdesertranger
View older results

Latest posts

Forum statistics

Threads
44,162
Posts
950,639
Members
36,273
Latest member
dannyphx
Top