Search results

  1. Big red square

    Blower motor draining battery

    When i plug the connector into the blower motor it drains the battery overnight. Any suggestions? 77 k10
  2. Big red square

    6 Lug front wheel studs Help

    So something like that will work as long as the Knurl size is the same?
  3. Big red square

    6 Lug front wheel studs Help

    I need longer wheel studs in the front of my 77 k10 Do i have to have the exact same groove spacing on the studs or any stud will work?
  4. Big red square

    D44 longer Wheel Stud P/N needed

    That's safe to do drill the holes?
  5. Big red square

    K10 NEED LONGER WHEEL STUDS.

    .
  6. Big red square

    D44 longer Wheel Stud P/N needed

    What do you do with the 6 lugs?
  7. Big red square

    K10 NEED LONGER WHEEL STUDS.

    Same boat what did you guys end up doing?
  8. Big red square

    Front end grinding when hard accelerating

    Let me take it apart today after work and get back to this thread. Thanks for all the info
  9. Big red square

    What motor is best for a swap on a K25

    How much power you think your making roughly?
  10. Big red square

    Front end grinding when hard accelerating

    Another putting it in 2wd and still hearing and feeling the grinding noise would rule out the front shaft wouldn't it?
  11. Big red square

    Front end grinding when hard accelerating

    Axle u joint Yes it does no i haven't changed those what is the centring ball? Yes 6 inch lift not sure about the angles just used the RC transfer case drop kit Let me try those tests. No all I did was the axle u joints on both sides and greased. I was thinking maybe i put the outer wheel...
  12. Big red square

    Temp gauge problem

    What if the truck stays on cold? Changed sending unit. Tested a different gauge. Use alligator clips to wire it myself still reads cold.
  13. Big red square

    Front end grinding when hard accelerating

    Yes
  14. Big red square

    What motor is best for a swap on a K25

    454 bbc IMO
  15. Big red square

    Front end grinding when hard accelerating

    hello i have a 1977 k10 and i had a griding noise and feel when i hard accelerate in 4wd and a squeal when turning in 4wd. Changed the u joints and the squeal is gone but now it grinds in 4wd and 2wd. What could it be wheel bearings to tight or loose? Dana 44 NP203 transfer with a part time kit.
  16. Big red square

    Crooked bed?

    How could i tell if my frame is twisted?
  17. Big red square

    NP203 fluid

    I have a part time kit installed as well not sure if that makes a difference.
  18. Big red square

    NP203 fluid

    Is it ok to use 15w-40 diesel oil in np203 transfer case? Also how much oil does it take roughly?
  19. Big red square

    NP203 Transfer case backyard install

    Thanks for all the help i ended up buying a trans jack. A few cuss words later and it's in.
  20. Big red square

    NP203 Transfer case backyard install

    Ok you convinced me ill be buying it.
  21. Big red square

    NP203 Transfer case backyard install

    that strap would hold it down also bigger area for it to lay on flat with out it moving back and forth.
  22. Big red square

    NP203 Transfer case backyard install

    I'm thinking about buying this jack(Dont want to) https://www.harborfreight.com/450-lb-low-lift-transmission-jack-61232.html But i would still need blocks since its so high.
  23. Big red square

    NP203 Transfer case backyard install

    The t case doesn't have a mount on my truck it just bolts to the transmission
  24. Big red square

    NP203 Transfer case backyard install

    Little confused what holes on the T-case will bolt to the crossmember? My cross member only bolts to the frame and transmission.
  25. Big red square

    NP203 Transfer case backyard install

    I'm trying to install my np203 transfer case with a floor jack on a truck with 6" lift and 35's Any suggestions?

Latest posts

Forum statistics

Threads
44,162
Posts
950,639
Members
36,273
Latest member
dannyphx
Top