Search results

  1. Ken B

    Brakes

  2. Ken B

    Brakes

    the pv tool that centers the pv while bleeding helps. I went thru 1 new chinese prop valve then spent a little more on a 2nd one and it didnt leak
  3. Ken B

    temp sensor

    thanks for the info. this not my original engine its a late 80s-90 engine. bushed to fit i did see that. guessing the bushing may try and come out when i try to remove sensor we will see. i think the sensor is a 13/16 socket to remove from the research I looked at. shoulda done this when the...
  4. Ken B

    What have you done to your square lately??

    Got the engine running yesterday. very pleased that it fired off so quickly. I have a new fuel system so was concerned about leaks , problems. New tank , lines, fuel pump. tested new fuel pump by cranking disconnected fuel line at carb into a milk jug, great flow. hooked up the fuel line to the...
  5. Ken B

    temp sensor

    I thought it was nailhead sensor that the head got broken off.
  6. Ken B

    What atf fluid needed

    Will just be a weekend warrior no towing
  7. Ken B

    temp sensor

    before i look at replacing this temp sensor, am I correct to assume the sensor is only the smaller diameter brass that is in the block? the outer brass is a bushing? thanks in advance
  8. Ken B

    What atf fluid needed

    T350 trans what fluid do I need? Dex /merc Dex 6?
  9. Ken B

    What is this sensor?

    this picture enlightened me, my sensor connection point looked like a hollow "pipe". looking at this picture i can now tell mine is a nail head that the "head" was knocked off. old thread still spreading information thanks
  10. Ken B

    Hello from kentucky

    Welcome from Indy
  11. Ken B

    Panel Gaps/ Body alignment

    Keith Wow. That's alot of trucks. You are great to share all that knowledge.
  12. Ken B

    What did we do before cup holders?

    Drink Faster?
  13. Ken B

    Panel Gaps/ Body alignment

    thanks probably the course i will take
  14. Ken B

    Panel Gaps/ Body alignment

    thanks for passing the help. or I might just stand there and stare at the truck trying to decide where to start......once I get started its fine, its just getting a starting point. Got the cab mounts tightened and torqued gonna get doors close if possible then get the fenders on. gotta loosen...
  15. Ken B

    Panel Gaps/ Body alignment

    pic of both side. just seems wide to me. can I put a flash washer between the door and the hinge on all bolts to push it back?
  16. Ken B

    Panel Gaps/ Body alignment

    I will get some pics I have just been scratching my head on getting the door to sit back farther in the cab. since the hinges have bolt from inside and outside. I am saying it is off I would say double what it should be maybe. Not looking for perfection, just close and something that doesnt grab...
  17. Ken B

    Panel Gaps/ Body alignment

    that makes sense. it just seems odd that the pass door seems to sit forward in the cab , big gap in the back(latch side) and no adjustability.....these are all "new to me" they werent from the factory together.
  18. Ken B

    Panel Gaps/ Body alignment

    all good info. thanks Basically every bolt is in place but non are tight.....hahhaa
  19. Ken B

    Panel Gaps/ Body alignment

    I feel like I am chasing my tail on body panel alignment. Looking for experience/ wisdom from others . I locked down the core support and hung fenders , doors are on the replacement cab, bed is on the frame. Just start from the core support and start trying to adjust panels? THe pass door is...
  20. Ken B

    What have you done to your square lately??

    I looked at my truck as I was in and out of the garage grabbing tools to work other projects. Seems like the hours disappear and I get tied up with other stuff constantly
  21. Ken B

    What’s IT Worth? (Post all “what’s it worth threads here)

    Look at sold prices on Mecum Auction to see what comps sold for? I went to Mecum Indy and some of the prices were insane.
  22. Ken B

    What’s IT Worth? (Post all “what’s it worth threads here)

    Such a good looking truck. Lots of value there but I don't know enough to guess.
  23. Ken B

    85 K10 donor and parts for sale

    I am ready for a little more "void" still got my truck but now its all the stuff I need to make into one cohesive unit...hahaha
  24. Ken B

    85 K10 donor and parts for sale

    Sold , had a guy pull up my drive today while i was doing yard work and wanted to talk about my donor, 45 minutes later he had a flat bed tow truck in my drive and some dead presidents .
  25. Ken B

    85 C10 Silverado step side brake line routing

    have you looked at the lines/drawings on LMC Truck for ordering. IIRC they show the routing. I got a complete set for my 81c10 stepper and it was all good.

Latest posts

Forum statistics

Threads
44,162
Posts
950,639
Members
36,273
Latest member
dannyphx
Top