Search results
-
What have you done to your square lately??
anyone know where to get these wiper motor bolts. classic industries says out of stock.... -
What have you done to your square lately??
today I reinstalled drivers door motor regulator and glass..pain in the A$$. reinstalled steering column, plugged in wiring to column, reinstalled wiper motor until,,,,the last screw , last "snug" the SOB snapped....3 steps forward and 1 back. Odd screw big head and small screw, might be tough... -
Anti squeak gas tank kit
I ended up using rubber water main gasket material for my strips. A perk of my job,working in the water treatment plant, leftover trash is another mans treasure- Ken B
- Post #5
- Forum: Tech Discussion
-
-
What have you done to your square lately??
I got new window motors to install. I am going to clay mitt the glass before install. Any seasoned vet have any helpful hints on reinstall of window regulator and motor... -
Question about wood bed stain and sealer for my 1987 Stepside
Great reminder thanks. Just dug In the trash and layer out the rag- Ken B
- Post #16
- Forum: Paint and Body
-
Question about wood bed stain and sealer for my 1987 Stepside
I thinned as per directions on container. 2pts paint thinner 1 part linseed- Ken B
- Post #14
- Forum: Paint and Body
-
Question about wood bed stain and sealer for my 1987 Stepside
Did a test, Linseed oil(thinned w mineral spirits), spar varnish, red chesnut stain and red oak stain. on back of red oak bed wood. I have Stainless strips and hardware truck is brown. My knee jerk reaction is Linseed oil. Its more about protection for me so the wood survives. And with a dark...- Ken B
- Post #12
- Forum: Paint and Body
-
Question about wood bed stain and sealer for my 1987 Stepside
I may try some boiled linseed on the bottom of a board and see what is looks like. Have used linseed for other things but that red oak is $$ dont wanna have to replace ....EVER haha- Ken B
- Post #11
- Forum: Paint and Body
-
Question about wood bed stain and sealer for my 1987 Stepside
Following ,,,,,I have red oak for my stepside and was wondering sealant.- Ken B
- Post #9
- Forum: Paint and Body
-
New Squarebody owner
Welcome from INDY lots of great info to be gathered here.- Ken B
- Post #18
- Forum: Introduction
-
Door rebuild - what should I get in preparation?
doing some research on window motors, I have to replace the drivers door window motor. I have it and the regulator out. My question is what supplier/manufacturer is good and which are cheapo. Just wanna do this once, where should I get a replacement motor for reliability. Thanks -
Does anyone recognize these?
Is Bucket EVER wrong ?- Ken B
- Post #4
- Forum: Stereo & Entertainment Systems
-
What have you done to your square lately??
Did some undercoating and satin black painting of inside of inner fenders and undercoating on bed wheel wells -
Stepside Bed Question
I am looking to do some spray on undercoating on the underside of my stepside fenders. I am assuming that I should NOT spray the seam where the fender meets the bedside so it can drain any moisture. Is this a correct assumption?- Ken B
- Thread
- Replies: 1
- Forum: Paint and Body
-
-
-
Square body meet Richmond Indiana
Anyone attending please take pics for those of us unable to attend. -
Need help with lights
I have been lurking on this thread, just re installed my fuse block and starting to re install the wiring , I will be back begging for help I am sure. I am already getting my mindset,,,,run 1 circuit get it working and stop. Gonna take a while but no tools will fly across the garage...- Ken B
- Post #15
- Forum: Electrical & Audio
-
ID this rocker step hole for me
Rust proofing like a company called rust check they drilled dozens of holes and injected oil like substance then it would rip/drain for hours on a lift- Ken B
- Post #6
- Forum: Paint and Body
-
Proud New 1976 Square Body owner!
Welcome from Indiana. Lots of good information around here. I have been sucking info up as much as I can- Ken B
- Post #6
- Forum: Introduction
-
Door Conduits
does anyone have any feedback on the HD Wiring Harnesses from LMC,,,,good/bad ? easy to install? tips?- Ken B
- Post #18
- Forum: Electrical & Audio
-
Square body meet Richmond Indiana
this happens each year when we vacation......and its so close and I bought a vehicle from the founders....stinks i miss it -
Door Conduits
just rehung my doors....all my door bolts were "temporarily misplaced" after lots of cleaning found them in the bottom of a 5 gallon bucket, so I hung the doors and looking into the wiring....I have LMC HD wiring harnesses and factory wiring is in tact. Heating up outside so doing indoor...- Ken B
- Post #17
- Forum: Electrical & Audio
-
