Search results
-
Intake Manifold Install
Need a new Ignition Control Module, Interesting did not have any issues before- Mango
- Post #67
- Forum: Engine & Performance
-
-
Intake Manifold Install
Yes still Code 42 going to check the wires to the ECM next The intake ports for the EGR were plugged used the old EGR could this be a issue- Mango
- Post #63
- Forum: Engine & Performance
-
Intake Manifold Install
GMBellew Checked all vac lines correct location most are new The T in the PCV line is Purge Signal Hose to canister Checked connections and wires look good Cleared codes let it idle to temp stalled when it reached Operating Temp Restarted it no engine light, idle was fine then idle dropped...- Mango
- Post #61
- Forum: Engine & Performance
-
-
Intake Manifold Install
Original Harness Wire Mold, wish it would run- Mango
- Post #57
- Forum: Engine & Performance
-
Intake Manifold Install
Goes to the canister that was there the whole time thanks It does connect to the TBI Could a bad temp sensor cause stalling- Mango
- Post #55
- Forum: Engine & Performance
-
Intake Manifold Install
Why would they fail now after a intake manifold gasket replacement- Mango
- Post #53
- Forum: Engine & Performance
-
Intake Manifold Install
Would a old ignition pick up cause the random stalling, it was fine before i pulled out the Distributor- Mango
- Post #51
- Forum: Engine & Performance
-
Intake Manifold Install
Rusty Nail EST wire clear thx Large ground strap to frame- Mango
- Post #50
- Forum: Engine & Performance
-
Intake Manifold Install
Yes Code came Back Where would I find That Manual- Mango
- Post #47
- Forum: Engine & Performance
-
Intake Manifold Install
That is Exactly where mine is, I painted the intake and used thread sealer would that be an issue? Rusty Nail what is your suggesion to locate the Grounds, Battery And small wire ground?? It was all fine before i Installed new Gaskets- Mango
- Post #45
- Forum: Engine & Performance
-
Intake Manifold Install
Added a additional ground strap to the frame, Cleaned surfaces to metal, Same issues runs for anwhile or drive Afew miles and instant shut off Move thhe ground to a new location?- Mango
- Post #43
- Forum: Engine & Performance
-
Intake Manifold Install
Thereis a ground on the Passenger side second bolt in the intake with the battery ground Check and was some bare wire repaired last year some time- Mango
- Post #41
- Forum: Engine & Performance
-
Intake Manifold Install
Thanks Guys No ground by the thermo- Mango
- Post #39
- Forum: Engine & Performance
-
Intake Manifold Install
UpDate code 23 gone code 33 vacuume hose not connected, The Dreaded code 42 is back checked ground wire ok Let it idle sounded great then just shut down no sputer its like i turned the ignition off hard start rough idling engine light came on Stumper- Mango
- Post #36
- Forum: Engine & Performance
-
Intake Manifold Install
Yes no stall, just Questioning if thats all it was I did clean the TBI when it was off with carb cleaner turned it upside down and blasted it must of gotten junk where it should not be Thanks- Mango
- Post #34
- Forum: Engine & Performance
-
Intake Manifold Install
Removed the IAC cleaned it check connections re installed took it for a small test drive no stall??- Mango
- Post #32
- Forum: Engine & Performance
-
Intake Manifold Install
Did that several times while checking codes, added a new ground strap to the frame cleaned out the bolt hole to remove thread sealant to get better ground Idles great rev it up sounds great short test drive across the parking lot stalled out Cleaned out all the electrical connections added...- Mango
- Post #30
- Forum: Engine & Performance
-
-
Intake Manifold Install
No did not remove it but i will check it out??- Mango
- Post #27
- Forum: Engine & Performance
-
-
-
Intake Manifold Install
disconnected the EST Connector when timing ,on Zero And re connected ??- Mango
- Post #21
- Forum: Engine & Performance
-
Intake Manifold Install
Latest cleaned the electrical connections on the TPS and cleared the ECM codes gone? Went for a test drive engine light came on hard shift ran like it was going to stall! Checked codes now code 42 came up just replaced the ICM in June Checked the wires all looked good, Cleared the ECM again...- Mango
- Post #19
- Forum: Engine & Performance
