Search results

  1. JKRamsey1991

    Steering Box Question

    That may be an option. I didnt even think about that being an option
  2. JKRamsey1991

    Steering Box Question

    I've got an 86 K20, with the engine build I ended up buying a pulley and belt kit that utilized an older style pump that necessitated new hoses as well. With that I have to run adapters from flare style to the oring style on the gearbox. I am having issues getting one of the adapters to seal...
  3. JKRamsey1991

    Gear Reduction Starter Praise

    Recently rebuilt the engine with some performance goodies for my old squarebody. Prior to that the starter always seemed to struggle and sounded awful. After the rebuild and the additional point or 2 of compression it was not cutting it. So I went to Autozone and picked up one of the gear...
  4. JKRamsey1991

    Oil dripping around starter

    Back of the engine common sources of oil; rear main, oil pan, distributor, oil pressure port behind the intake manifold, valve cover. Less common would be the cam tunnel plug in the back of the block and the intake manifold itself can have oil seep. I would pop the inspection cover off the...
  5. JKRamsey1991

    Engine Rebuild Kit Recommendations

    I would get out some calipers/mics and really start measuring everything. It its really tight something is most likely wrong. Make sure the ring depth on the pistons matches the ring spec. I know you can get different oil ring groove depths 0.200 vs 0.165 i believe that may cause an issue but...
  6. JKRamsey1991

    Engine Rebuild Kit Recommendations

    I am currently buttoning up the rebuild on my small block. I found it was cheaper to piece together a the stuff than buy a kit if doing a simple re ring and bearings for me. I wanted to upgrade a few of the parts like oil pump and stuff and it equaled out to me saving money over buying the kit...
  7. JKRamsey1991

    1986 Engine Wiring Question

    Well maybe I called the module the incorrect name. It is the Emission Control Module not technically the AIR module.
  8. JKRamsey1991

    1986 Engine Wiring Question

    I'm with you really. I have no clue how the AIR module works or any of that. It just appears the white/brown wire is the 12volt feed to that module and the white wire to the distributor plug. So I think just splicing those two together and bypassing the module would do it. Currently all other...
  9. JKRamsey1991

    1986 Engine Wiring Question

    I guess everyone is about like me and hates wiring/wiring diagrams lol.
  10. JKRamsey1991

    1986 Engine Wiring Question

    As I am in the process of rebuilding the engine in my truck I wanted to clean up the wiring while I am able. My truck has all of the emissions stuff deleted (AIR smog pump EGR etc). I want to delete the AIR control module. I see the AIR module feeds the distributor from the white wire. Looking...
  11. JKRamsey1991

    SBC Cylinder Head Decision

    The motor is coming out of the truck in a couple weekends. Will tear it down and decide from there. Based on the feedback probably will go with the AFR's unless I run into unexpected internal issues.
  12. JKRamsey1991

    Engine swap

    As long as it is not a reverse rotation marine engine it should swap in. Id try to find the specs on the cam before assuming it needed swapped as well. Swap everything over from your engine (water pump, pulleys, exhaust manifolds) and you should be set. Id definitely try to wash out as much of...
  13. JKRamsey1991

    SBC Cylinder Head Decision

    Truck has 4:10 gears in it so I can get by with a bit more cam. From what I have been researching was leaning towards a cam similarly spec'd to the one Catbox mentioned or one of Comps Xtreme 4x4 cams like the 270H seemed like a good match for decent on road stop light performance and driving...
  14. JKRamsey1991

    SBC Cylinder Head Decision

    They compared the Speedmaster, AFR and the Summit head. The summit is supposedly made by Brodix so I guess it compares two of the three. I'm definitely leaning towards the AFR's but wondering what everyones experiences opinions are.
  15. JKRamsey1991

    SBC Cylinder Head Decision

    Good Morning, I am planning to rebuild the 350 SBC for my square over the winter. Currently in the parts choosing and planning stage. I am planning on new cylinder heads for the build with end goal of between 350-375HP. Truck is 4x4 will see some use pulling light loads but is mainly a cruiser...
  16. JKRamsey1991

    Improve 1/8 mile et

    Have you thought of rear gear swap? Most 1/8 mile guys I know run like 4.56 or 4.88s even. Whats your RPM at the top of the track?
  17. JKRamsey1991

    K20 Front Brake Dust Shields

    You must be better at googling than me because I ain’t found any yet for the front lol!
  18. JKRamsey1991

    K20 Front Brake Dust Shields

    Does anyone know where a man can buy the front brake dust shields? Mine are pretty well rusted and shot, but I can’t seem to find any for the 4wd models.
  19. JKRamsey1991

    K20 Heavy Duty Spring Option

    The front springs may have been replaced at some point I guess. Owner I bought it from only owned it since 2016 and he said he did not change them so still 30 years time there they could have been replaced.
  20. JKRamsey1991

    K20 Heavy Duty Spring Option

    According to the RPO tag it was a fleetside. The homemead flatI think makes the wheels look really inboard because of the long skirts and extra width of the bed.
  21. JKRamsey1991

    K20 Heavy Duty Spring Option

    Recently acquired an 86 K20 with the heavy duty frame and suspension options (C6P, F60). Do these trucks sit higher than a standard K10/K20? This truck as far as I can tell is all original suspension besides shocked but it seems to sit higher than trucks I have had in the past. Does anyone...

Latest posts

Forum statistics

Threads
44,161
Posts
950,631
Members
36,273
Latest member
dannyphx
Top