Search results

  1. scrap--metal

    Fuel only gets to engine when tank is out of the vehicle

    You are correct about where to disconnect the line. It has to be after the fuel pump, which likely means you need to disconnect the fuel line at the carb. The picture below shows the fuel line disconnected from the carb. Once the fuel line is removed, the fuel filter can be checked and/or...
  2. scrap--metal

    Whats the going rate for shortening a driveshaft? I think I got....shafted

    Last year I was quoted $240 - $280 JUST IN LABOR to cut, shorten/lengthen, and balance a driveshaft. No U-joints, no slip yoke, and no new tube itself. I wasn't going to pay that, so I found a NOS driveshaft on eBay and had it shipped to my door for just under $200. You did fine for $300.
  3. scrap--metal

    Truck left me stranded today.

    That's not horrible oil consumption. It's sure not normal, and you're right to be thinking ahead, but it'll keep going for many miles if it's not fouling plugs and otherwise running fine.
  4. scrap--metal

    1978 k10 radio patch panel

    Here's what I did to fix the same issue earlier this year: PO's hack job that I started with. Unfortunately the cut is visible beyond the bezel. After the bezel was removed. Repair section cut from a donor truck, which was already cut for a CD player. I got it for free, so I couldn't...
  5. scrap--metal

    Battery posts corrosion wtf

    Never seen those adapters before, but I might need to get some. The battery in my K20 is questionable, and it's only getting colder this time of year. Snow will be flying soon enough. I got a good 2 year old battery with top posts in my garage though. Adapters like that would make it usable...
  6. scrap--metal

    Engine loses power when shifting gears(auto)

    I have to echo Eric on that. It's a bad idea. The O-ring and the stamped steel lock ring will seal the top of the tank without any extra protection. Silicone O-ring lubricant is a good idea. It can be assembled without, but that gives the O-ring a chance to bind and pucker out of place...
  7. scrap--metal

    Engine loses power when shifting gears(auto)

    Definitely change the filter inside the carb. If that filter has not been changed yet, that could be the sole source of your power loss.
  8. scrap--metal

    Engine loses power when shifting gears(auto)

    Personally, I'd fix the fuel tank before anything else. If you know it's leaking and rusty, it's rusty on the inside too. Your engine and carb don't like orange tinted gas with chunks of iron in it. How bad was the fuel filter when you replaced it? My K20 had a gutless issue too. It ran...
  9. scrap--metal

    Starting up after sitting for up to 7 months?

    And sitting for a few months is no big issue. At least it's not the cause of the existing issues.
  10. scrap--metal

    Starting up after sitting for up to 7 months?

    My K20 ran great on the test drive, but wouldn't maintain highway speed on the drive home. Filling the gas tank washed all the loose rust into the fuel and it plugged up the fuel filter twice on the drive home. You have the right idea starting with the fuel filter. Good luck! If the filter...
  11. scrap--metal

    C10 lifted 4.5” max tire size

    I agree with Grit Dog that it looks perfectly proportional the way it sits. It almost looks like a factory K20 height, or a little taller. Keep the 32's. 33's could look good, but wouldn't be worth swapping. 35's would look large IMO.
  12. scrap--metal

    FM acting weird in Factory Radio

    So the factory FM radio in my K10 has been acting goofy for the last several months. I can pick up FM just fine in the Minneapolis area and immediate suburbs, but as soon as I get out of the county FM reception is non-existent. AM still works fine. It's like I cross over the river and FM...
  13. scrap--metal

    '79 Camaro Restomod

    Sounds like you have a very solid, but involved, plan. I dig it! Please take lots of pictures when you center up that 10 bolt. Someday I'd like to do that to my car if I can muster up the ambition. Regarding the '80-'81 style, do you also plan to add the Z/28 rear quarter flares from those...
  14. scrap--metal

    '79 Camaro Restomod

    It's odd that they didn't have better fixtures for the axel assemblies in these F-bodies. I guess that might've cost something extra... Thanks for confirming that this is probably applicable to Andy's Camaro too.
  15. scrap--metal

    '79 Camaro Restomod

    Cool car, Andy. Just read through the whole thread. I doubt you'll be able to get 275's up front. Especially since you've gone with drop springs (good decision). I had 245/45R17's on the front of my '79 and they would rub bottom rear portion of the wheel well at the steering locks. They...
  16. scrap--metal

    Favorite Project Truck Sales Pitches

    "Rebuilt engine" That's an engine rebuilt with two cans. One can of degreaser and one can of spray paint.
  17. scrap--metal

    Favorite Project Truck Sales Pitches

    Hey!!! My K20 had a few wire nuts in service when I bought it. They've since been removed and replaced with soldered connections. I bought my truck knowing it had been hastily slapped together for sale, but I still get surprised from time to time.
  18. scrap--metal

    Vacuum switch, break switch, and wiring for 700-R4

    Yes, there is a way to do it. I'm not exactly sure how though. The schematic below is one example of how our trucks could be wired. The low vacuum switch and the brake switch can both interrupt the lock-up. That's what confuses me on where the indicator light should go. Lot's of aftermarket...
  19. scrap--metal

    C20 for towing

    A friend of mine used a K20 as his primary tow vehicle for decades until about 5 or 6 years ago. He'd take the K20 and tow his drag car in an enclosed trailer from Minnesota to Ohio, and other drag strips closer to home. His K20 has a 350 and a TH400 and it always did fine. The catch was he'd...
  20. scrap--metal

    The 383 is finally going in!

    At the very least, remove the cap and rotor. They're easy to break if they bump the firewall. Probably best to have the entire distributor out. Others will have more wisdom to share.
  21. scrap--metal

    Stumped, fender marker/turn light issue

    If the LEDs you have are polarity specific, I'm confused how they worked correctly after the initial installation. I believe you when you say they did work, but it goes against what Wayne explained in the turn signal circuit (post #7). It seems as though they should never have worked (i.e...
  22. scrap--metal

    Stumped, fender marker/turn light issue

    ^ Has that been tried yet, in combination with the incandescent bulbs?
  23. scrap--metal

    Stumped, fender marker/turn light issue

    The "event" was likely time and repeated use of the transistor(s) within each LED assembly. The side marker failure should be independent from your dash lights. Like Wayne explained, below: It's the transistor man!
  24. scrap--metal

    83 c30 dually 454

    Lol. That could be it! I've seen some pretty irrational customizations over the years, but I can't imagine why some one would cut the rear frame rails. It's a shame no matter what their intentions were. Maybe they had a flat bed off something else that they planned on installing at a future...
  25. scrap--metal

    Stumped, fender marker/turn light issue

    LEDs in your dash are just fine. No need to change those out based on my experience. LEDs in the side markers is asking for trouble based on the circuit design. @Turbo4whl explained it very well in my opinion. You shouldn't need an engineering degree to pick up what he's laying down. How...

Latest posts

Forum statistics

Threads
44,163
Posts
950,690
Members
36,276
Latest member
2manysquares2care
Top