Search results

  1. scrap--metal

    New From Maryland

    Welcome, and great introduction story! Any picture love for the C30?
  2. scrap--metal

    Engine Doesn’t Like Starting When Hot

    All the suggestions above are good, and any one of them could be a possibility. Does your truck have headers? ^ This was happening to my Camaro last summer. Would start great cold, but hot it seemed like the timing was too advanced to start. In reality the old started was too tired to turn...
  3. scrap--metal

    WTB Gun Rack

    Got a link to something equivalent to what you got? The ones I looked at online don't seem the same.
  4. scrap--metal

    Show your daily driver

    Sorry in advance for the novel. I hope my description can paint you a good mental picture... The kit comes with a hollow guide bolt that the long drill bit fits in. That guide bolt gets threaded into the carrier above the broken bolt (the shaft locking bolts usually don't break off flush at...
  5. scrap--metal

    WTB Gun Rack

    Let me know when they turn up. Hunting season is still a long ways off, so I'm in no particular rush. Thank you!
  6. scrap--metal

    Show your daily driver

    There's no need to use brute force to remove that pin with the broken bolt. I ran into the same issue when trying to replace axle tube seals a few years ago, and my buddy brought over a kit like shown in the link below. It worked well and he got the busted bolt out relatively easily. It's a...
  7. scrap--metal

    WTB Gun Rack

    @Doppleganger that's exactly what I had in mind. Is it steel? How much do you want for it? While driving home from work yesterday, and further contemplating this idea, I realized that the rack could interfere with the headliner/trim that I've have and plan to add to my K20. Or maybe (best...
  8. scrap--metal

    WTB Gun Rack

    I'm looking for a cheap gun rack that will work with a sliding rear window in my K20. I've seen some generic ones on Amazon, but I have no idea what will work well and look appropriate in our trucks. Let me know if you have something laying around collecting dust. If anyone has experience...
  9. scrap--metal

    Haynes manual suggest silicone dielectric grease for ignition module?

    ^ I'm in this camp. As long as it's thermally conductive enough, it should work. That makes me wonder what the thermal conductivity of the paste they used in the factory was? If the new stuff (thermal paste, dielectric grease, etc.) has the same thermal conductivity value (K measured in...
  10. scrap--metal

    Power Steering pump

    Sorry I don't know about the one bolt vs two bolt attachment, but I have one more thing on power steering for you @My78truck. Assuming you're ordering a new high pressure line, pay attention to what style you're ordering if the look of originality matters to you. The new high pressure lines...
  11. scrap--metal

    New Member! Square Body Collector!

    That looks like heaven on Earth! Thanks for the follow up pic. It's awe-inspiring. We love lots of pictures here, if you haven't caught on to that already. Keep hanging around on the forum and you'll gradually figure out all the functionality. It's relatively user friendly.
  12. scrap--metal

    Windshield Woes

    Interesting. I used a gasket with a separate lock strip. Maybe that's why it fit tight? The hardest part of my install was getting both ends of the lock strip in at the bottom center of the windshield, with the little clip on it. I had to roll around on my hood like a bikini model covered...
  13. scrap--metal

    Windshield Woes

    Thanks for the clarification, and all the additional details. I agree that the sealant doesn't seem to be a requirement based on the videos available. I haven't had my K20 in the rain since I replaced the windshield and gasket with my dad last summer, so it hasn't really been tested yet, but...
  14. scrap--metal

    Windshield Woes

    Randy, did your local glass guru install your windshield with or without sealant, urethane, etc.? I'm trying to establish whether or not the sealant excuse you got from Precision is justified, or a cop out explanation for when things don't work out as planned.
  15. scrap--metal

    New Member! Square Body Collector!

    Welcome! How many squares do you have in your collection? Lots of us have more than one, but I'm wondering if @AyWoSch Motors might have some competition here ;)
  16. scrap--metal

    Bought a kid that isn't mine a 1976 Nova...

    Everybody and their brother would've given $250 for that car, myself included if it was semi-local. Hell, my wife has been asking for her own hotrod, specifically a Nova. She likes the earlier 2 doors, like everyone else, but this would've fit the bill. It's sad to see the cookie crumble like...
  17. scrap--metal

    Any tricks to thread speedo cable back through grommet in firewall?

    I just did this a couple weeks ago. My K20 had a 2wd speedo cable that didn't reach the transfer case. I think it's easier to pull the grommet out of the firewall, position it approximately along the length of the speedo cable, and then feed it back through the firewall and poke the...
  18. scrap--metal

    Cab and bed gap

    Seems like the approach I'd take as well.
  19. scrap--metal

    3/4 Ton Dana 44 vs 10 bolt caliper brackets (backing plates)

    Do the caliper brackets/backing plates from a 3/4 ton Dana 44 interchange with the backing plates on a 3/4 ton 10 bolt? Are any minor modifications necessary? The driver's side plate is mostly missing from the 10 bolt under my truck, and I may have a lead on some Dana 44 backing plates. Just...
  20. scrap--metal

    Bought a kid that isn't mine a 1976 Nova...

    Pussificatation right there. That was a super sweet ride for a young man to learn on.
  21. scrap--metal

    Squares since I was in diapers

    Welcome. And good looking truck!
  22. scrap--metal

    WTB 3/4 Ton Front Brake Caliper Plates

    I need the same thing. You beat me to the post, but I bet mine are in worse shape than yours.
  23. scrap--metal

    What's the best way to drain the gas tank?

    I've never seen a screen either. I think you need to try harder with a smaller diameter hose. It is kind of a pain to get the hose down in position. I've had success siphoning with an old air compressor hose.
  24. scrap--metal

    ESC need someone that knows more about ESC system than I do

    I'm glad to hear your making progress. You sure deserve it after all the work you've put into your ESC system.
  25. scrap--metal

    New to this forum and looking for best options for a new radiator

    Welcome to the forum. Is the radiator leaking, or are you having a cooling issue? Cooling issues can commonly be caused by things other than the radiator.

Latest posts

Forum statistics

Threads
44,162
Posts
950,642
Members
36,276
Latest member
2manysquares2care
Top