Search results

  1. 81squared

    Pulley pulling

    I’m replacing my water pump and steering pump. I’d like to reuse the pulleys. I purchased a pulley puller last night. Seems like it would work on the water pump but the pulley on steering pump seems different. Any input on both pulleys would be appreciated thanks
  2. 81squared

    Grille brackets

    any idea where to get the extended ones ( long reach ) ? Thanks
  3. 81squared

    Grille brackets

    thank you very much !! I did not have these brackets.... i had done some homework a few minutes ago and found a photo with these brackets. I searched good ole E Bay and found a set for 20 bucks !!! so pumped. question, what type of nuts do you use on the bracket to accept the grille screws ?
  4. 81squared

    Grille brackets

    This is the grill I want does this use face screws or the back mounting brackets. these web sites suck for info. No diagram of the back. Nothing. thanks
  5. 81squared

    Grille brackets

    does anyone have any pics of a 80 K10 or C10 grille ? i see 80 grilles on ebay but they show 3 screw holes on the top of the grille ... are they using the holes from the chrome piece or do the use the nut on the vertical support ? Sorry im just trying to get the correct grille thanks
  6. 81squared

    Alternator type

    Thanks. Yes I had a big block nova just before this. Totally used to less of everything.
  7. 81squared

    Alternator type

    Is this a 3 wire or a 1 wire. I see 3 wires but not sure. thanks
  8. 81squared

    Grille brackets

    OK thanks so if Im understanding this.. 73- 80 had the chrome detail on rad support and the grille mounts using the nuts on the vertical supports , if this is accurate wont all grilles from 73 to 80 have tabs on the back of the grill to attach brackets ? 81 and up use face screws into...
  9. 81squared

    Grille brackets

    Im sooo confused ... lol My truck is a 1980 K10 I dont know why my username is 81Squared, mustve been late at night. So .... My truck is 80, i removed the chrome today, there were 7 holes in the lip of support. Since my truck is a 80 are the mounting locations different ? I want to buy a new...
  10. 81squared

    Grille brackets

    I don’t see any mounting holes … I assume they are under that chrome strip ?
  11. 81squared

    Grille brackets

    Ok so I’ll look for the holes. It was weird , the radiator support had pre installed nuts to accept the custom bracket ? Weird … thanks
  12. 81squared

    Grille brackets

    Also… my lower filler has this chrome cover, do all Scottsdale’s come with these ? I’m hesitant to put it back on. anyone have any front end pics I could look at their grills ? thanks
  13. 81squared

    Grille brackets

    My truck came with a billet grille. I want a stock one. The old one has these brackets. do the original grilles utilize these same brackets. new grille seems to only be the grille. No mounting brackets included can I reuse these ?
  14. 81squared

    So many vac lines !!

    What kind of alternator is this ? A 3 wire ? Or a 1 wire ? These ports on the other photo … can all these be eliminated? I was hoping for a regular t stat housing like the older models
  15. 81squared

    So many vac lines !!

    I will be donating whatever is salvageable. I will post a list of parts when I have everything off the motor.
  16. 81squared

    Trans Cooler lines

    Hello , I would like to remove my old dented and patched trans lines, I would like to do 6AN braided, i see kits with 50 inch pre made lines. I tried to measure but its difficult , has anyone used these or know if 50 inch will be long enough, they sell 70 inch but I dont want to much excess...
  17. 81squared

    So many vac lines !!

    I assume a lot of what you mentioned runs through the vac system of the carb ? Once the carb is gone i just re route lines to items you mentioned... auto trans, heater controls, there is a port on the thermo housing, is that what I would need to feed these items in need of vac ?
  18. 81squared

    So many vac lines !!

    I am new to later model 350s, there are a ton of things on this intake and carb that Ive never seen. Let me preface... Im installing a Holley Sniper EFI complete system, rather than try to figure out what I have going on vac tube wise, let me ask this... After the carb is gone and the...
  19. 81squared

    Rear Wheel is Stuck !!

    8LB sledge... one easy pop this morning and she came free !!
  20. 81squared

    Rear window clarification

    my apologies for not posting a pic, Im usually in the house when I think of half the questions. I will do a better job !! Thanks for all the input I will do a conclusive photo op soon, its crammed in my garage for now.
  21. 81squared

    Rear Wheel is Stuck !!

  22. 81squared

    Rear window clarification

    sorry for so many posts... I was told my truck had a stock all glass ( non slider ) rear window when it came from the factory. Truck has a aftermarket slider retrofit into the original rubber gasket. I want to replace the window and the gasket after I paint the truck. 2 questions... Are...
  23. 81squared

    Rear Wheel is Stuck !!

    Spent the last 3 hours sweating my face off trying to remove a stuck wheel. the other 3 came off no problem, rear driver... not so much can of liquid wrench....check Beat rim for hours....check Drove short distance with lugs loose ..... check Said a few four letter words in front of my...
  24. 81squared

    Radiator removal

    thanks for the replys, Im having a shop piece the manifolds and to the exhaust pipes. they dont make the Y pipe anymore... fun stuff !! Im not looking for power, Im looking for quiet stock sound. I am however converting to EFI in the coming months Purchased Holley Sniper EFI with the fuel...
  25. 81squared

    Radiator removal

    second question, kinda off base but... my truck came with headers, I want to replace with stock manifolds. the collectors on the headers join with the muffler pipe rather far down the line, with the stock manifolds there seems to be a pipe missing connecting the manifold to the muffler pipe ( if...

Latest posts

Forum statistics

Threads
44,161
Posts
950,631
Members
36,273
Latest member
dannyphx
Top