Search results

  1. Camar068

    Ignition Resistance Wire-Needed or Nah

    Also, another way to test the wire thats getting hot is to ohm it out to the battery. DISCONNECT THE BATTERY FIRST. Then put one meter lead on the positive connector that connects to the battery, then put the other lead on that wire thats getting hot. It should be close to zero with the key...
  2. Camar068

    Ignition Resistance Wire-Needed or Nah

    sounds like you have a wire/connection thats about to break. Imagine it like too small a wire for something that draws a lot of power. Follow it back and check for wire pinches, corrosion....anything that would cause it to not be a solid run. Also, you might be running too much on that one...
  3. Camar068

    83 K5 Blazer LS swap issue

    if you have the range selector unplugged on the trans, there's 2 wires I believe that need to be connected together on the ECM. Check the LT1swap chart and it should say it. Something in the nature if "if no range sensor" do this.
  4. Camar068

    Ls swap

    shouldn't he be able to cut the shaft on the 2wd shaft after removing the tail housing? Then get a trans adapter from a 4x4 4l60e.
  5. Camar068

    Engine lift points

    Love the one I got. The screws are kept on the plate and you pull out what you need. Solid and secure to the block. Nothing wrong with chains, but there's no hunting bolts/washers and setting height of chain when using a block plate. I would NOT use a plate that bolts where a carb is...
  6. Camar068

    Removing engine and trans.

    yeh I need to get one lol
  7. Camar068

    Removing engine and trans.

    Good info. I always start up front and save the drive shaft/crossmember out for last as I know it's gonna leak fluid out the trans. At that point it's a "lets get it out quick" for less of a mess.
  8. Camar068

    What have you done to your square lately??

    Been there....leaks again. Going with another option. Might even install sprayers on the cowl.
  9. Camar068

    What have you done to your square lately??

    Washer fluid reservoir leaking again. I had to try this. The stock pump isn't strong enough to pull fluid with this setup. I'll probably go with a 2 liter aluminum tank from Amazon for $30 and a different pump. Then again, might just upgrade the pump and let it fly.
  10. Camar068

    Most affordable shipping for body panels?

    We have a guy that I found on Craigslist. He supplies the body shops as well as the DIY'selfer. You'd be surprised, check craigslist to see if you have someone in your area that does the same. His prices are 5-10% higher than online (before shipping) and he delivers free to our local Hardee's...
  11. Camar068

    LS swap fuel system

    What make/model pump are dependable these days? I put in the ACDelco EP381 and they want $160+ for it now. [edit] this was added to a 87 burb sender/tank Little hijack, sorry OP, but it's for your benefit as well.
  12. Camar068

    What have you done to your square lately??

    great idea, never thought about that.
  13. Camar068

    K20 Suburban Flaming River tilt column (also Wolff Engineering bearing)

    I was really close to buying one, but I reminded myself that the issue I had with mine coming loose was because the previous owner didn't install the stock replacement correctly. So I, not knowing any better, installed it the same way. Same issue. After I looked at it and figured out the...
  14. Camar068

    Looking For Jeep Steering Shaft

    if you got a pick n pull yard close to you, check their website for the correct models. If you see multiple, grab them all and share the wealth and sell or trade here. After the 2nd one, you'll have them out in about 7 minutes per shaft if not less.
  15. Camar068

    LS swap fuel system

    Thanks for the reminder. Been a while since I've thought about why I went in tank. @KennedyHill don't want you to miss this reminder for me.
  16. Camar068

    Bed mount winch

    you got me thinking about the floor bolts. Maybe just weld some thicker nuts to the front four and have a plate with the winch already mounted to it. Like you said, have to deal with the nuts sticking up. Or even 4 nutserts on the lower ribs of the bed. Leave the bolts in when not in use...
  17. Camar068

    For you LS swap guys.

    If your using a non-plastic tank radiator, and have a radiator shop close enough, they can install a fitting just below the cap for the steam vent line. If your good at sweating, you could prolly do it yourself.
  18. Camar068

    What new tools have you got lately?

    normal ceiling in the garage I got these and paid ~$20 for longer extensions. They daisy chain so you only plug one in. So for ~$65 you get 6 lights, not including flashing if you don't have reflectors/flashing. Cardboard and metal tape is cheaper than flashing I'm sure....just an option...
  19. Camar068

    Bed mount winch

  20. Camar068

    Bed mount winch

    Bed winch mount frame thoughts. No welding to the vehicle. Bolt to the 2 vertical square things on the front (sorry don't know what they are called), and bolt angled bars to bed bolts. Only welding is on the winch frame itself. Can be removed. The tubing is 3/8" thick. Main use would be to...
  21. Camar068

    83 K5 Blazer LS swap issue

    @iamtherealJayy yup, disconnect the battery, then put your meter on ohms. Then put a lead on the negative battery cable, and test EVERY ground connector on the ECM connector. After that check all your wires to the throttle. The p0650 is an issue with the bulb/indicator you have wired for the...
  22. Camar068

    For you LS swap guys.

    worthy of reading, hope it helps. Google ls swap squarebody windstar for more info. It will be custom, but not difficult. Windstar 1 TYC windstar fan
  23. Camar068

    LS swap fuel system

    as much as I hate to say, I wish I had installed an external fuel pump. This way in the future, when in doubt you can get to it easier to swap. Just a thought on where you're at right now. Also put it where you can get to it easily. I put mine in the tank so "it wasn't so loud" as most say...

Latest posts

Forum statistics

Threads
44,162
Posts
950,639
Members
36,273
Latest member
dannyphx
Top