Search results

  1. G

    Cruise control works for a while then starts to lose speed

    agree, sounds like it is having an issue holding vacuum. check the hoses and the vac reservoir on the driver side fender under the hood in addition to the pod that attaches to the throttle.
  2. G

    Issues with seatbelts

    rough cost and turnaround time?
  3. G

    Intake Manifold Install

    I've used the paste it comes with normally. no issues with early failure of AC Delco
  4. G

    Intake Manifold Install

    make sure it is an AC Delco. it's a common failure point and I carry a couple spares in the truck at all times...
  5. G

    Need ideas for a modern steering wheel.

    yep, that's what I have! my burb was equipped with just about every option, so it is not surprising that the wheel was an option.
  6. G

    Need ideas for a modern steering wheel.

    I like the wheel on my 1990 suburban. I think 88-94 are all the same and likely are a direct replacement.
  7. G

    Intake Manifold Install

    if it wasn't doing it before you replaced the manifold, and is new after, it is likely something that got touched somehow. I'd guess the issue to be in the ICM harness in the EST wire or one of the 2 reference wires. the issue could be in the wire or the connectors themselves. did you go through...
  8. G

    Intake Manifold Install

    I don't think plugged EGR will result in 42. it will eventually throw a code when it self tests at highway cruise. but I think it is 32
  9. G

    Intake Manifold Install

    is it still code 42? because if it only does it at operating temp (likely when it hits closed loop), it makes me think it may not be ignition related.
  10. G

    Intake Manifold Install

    I'd still look at the vac hoses. the cannister, PCV, EGR solenoid, and MAP sensor should all come off different TBI ports. some are manifold vac and some are ported vac and it probably matters that they are all on the right ports. that might not be the issue, but while you are messing around may...
  11. G

    Intake Manifold Install

    did you try to follow the diagnostics for code 42 in the drivability manual?
  12. G

    Intake Manifold Install

    what is this vacuum arrangement? looks like something that should be hooked up to the TBI is Teed into the PCV valve line?
  13. G

    Best brand for LED conversion?

    I dont have pictures of the trimming. you only have to trim to fit a 90degree bulb. if you use the straight 9006xs and 9005xs straight bulbs they come with you don't have to trim at all. I still run the 9005xs in the highs because they are actually plenty bright and you would also have to trim...
  14. G

    Best brand for LED conversion?

    not a lot of support for 89-91 given the odd size and limited years of use. the LMC housings with glass lenses with the adjuster buckets trimmed to fit a 9012 bulb is a good option that I am running. I have thought about dropping in a diode dynamics SL1 LED bulb, but haven't bit the bullet yet...
  15. G

    Intake Manifold Install

    https://www.gmsquarebody.com/threads/1973-1991-service-manuals.14499/
  16. G

    Intake Manifold Install

    ground work best on bare metal. although I am not sure if that is the result of your code 42 (if you are still getting code 42). did you disconnect the neg terminal to clear codes and try again? if code 42 comes back, follow the diagnostics in the drivability manual.
  17. G

    Intake Manifold Install

    my ground is here next to the Coolant Temperature Sensor
  18. G

    Intake Manifold Install

    several TBI sensors use that ground. it comes out of the harness by the coolant temp sensor wires.
  19. G

    Intake Manifold Install

    code 42 only sets when the EST wire is disconnected. not sure if anything else in ICM will set it (which is certainly frustrating sometimes to diagnose). check the connection at the disconnect to set timing and at the ICM to be sure the connectors all look good.
  20. G

    Diagnosing white smoke on startup

    on my 1990 TBI the valve is in the passenger side valve cover and connects to the front of the tbi. the driverside is just a plastic hose connecting the other valve cover to the base of intake below the air filter.
  21. G

    Intake Manifold Install

    must have had something stuck in one of the tbi ports somewhere causing the issue.
  22. G

    Intake Manifold Install

    The question marks are confusing. Did it run fine and not stall after that?
  23. G

    truck runs hot

    Did you try a new instrument cluster gauge?
  24. G

    truck runs hot

    the computer uses the temp sensor next to the thermostat housing. so don't use that location.
  25. G

    Intake Manifold Install

    check to make sure you have all the vac lines hooked up correctly to the TBI. you may also check the EGR (or take the vac lines off at the solenoid and plug them) and see if that helps. does it seem like it is loading up on fuel and flooding itself out? do you have access to a scanner or...

Latest posts

Forum statistics

Threads
44,162
Posts
950,642
Members
36,275
Latest member
2manysquares2care
Top