TheBigBlue2500
Junior Member
- Joined
- Nov 16, 2024
- Posts
- 16
- Reaction score
- 18
- Location
- Bellefontaine
- First Name
- Nathanael
- Truck Year
- 1982
- Truck Model
- 2500
- Engine Size
- 6.2
Yeah flexplate, sorry been a long 2 weeks...
How many bolts hold the transmission on and where?
- Thread starter TheBigBlue2500
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
grummy
Junior Member
- Joined
- Aug 21, 2024
- Posts
- 15
- Reaction score
- 34
- Location
- Midwest
- First Name
- Chris
- Truck Year
- 1983
- Truck Model
- C1500
- Engine Size
- 305
Do it a few times in a week and it gets real easy ! I did an (1) out, in, (2) out in and an (3) out in all in a week while I was "checking" used transmissions. I'm 65, and I did it myself. Yes, LONG extensions expose the top bolts once the rear of the trans is lowered a bit.
I used to do them with a floor jack, but I tell you, my buddies Trans Jack (like in link below) made it much, much easier. If you can find or rent one rather than using a floor jack, do so ! Jack the truck up as high as you can get it right off the bat. Use good jackstands !
Don't forget to have a small hydraulic jack and some blocks to put under the oil pan so the engine doesn't hang back on the firewall, and it also helps for quick realignment on reinstall. Too, for reinstall, it can be helpful to put a longer stud in the midway holes for alignment that you can see better. Once slid in, get the top and bottom bolts pulled up, remove the studs and put in those two bolts.
Make double sure your torque converter is pushed into the tranny proper before pulling that tranny up to the belhousing. And, watch your wiring harness over the top so that doesn't get pinched. It's hard to see in there so look closely.
I used to do them with a floor jack, but I tell you, my buddies Trans Jack (like in link below) made it much, much easier. If you can find or rent one rather than using a floor jack, do so ! Jack the truck up as high as you can get it right off the bat. Use good jackstands !
Don't forget to have a small hydraulic jack and some blocks to put under the oil pan so the engine doesn't hang back on the firewall, and it also helps for quick realignment on reinstall. Too, for reinstall, it can be helpful to put a longer stud in the midway holes for alignment that you can see better. Once slid in, get the top and bottom bolts pulled up, remove the studs and put in those two bolts.
Make double sure your torque converter is pushed into the tranny proper before pulling that tranny up to the belhousing. And, watch your wiring harness over the top so that doesn't get pinched. It's hard to see in there so look closely.
Ricko1966
Full Access Member
- Joined
- Apr 11, 2017
- Posts
- 5,585
- Reaction score
- 9,066
- Location
- kansas
- First Name
- Rick
- Truck Year
- 1975
- Truck Model
- c20
- Engine Size
- 350
I don't even pull the transmission doing flexplates,I've written it up before,the condensed version is replace 2 of the engine to transmission bolts with long starter bolts,slide the transmission back on the bolts and you'll have enough room to R&R the flex plate.
GTX63
Full Access Member
- Joined
- Nov 27, 2022
- Posts
- 951
- Reaction score
- 3,875
- Location
- Tennessee
- First Name
- Ty
- Truck Year
- 1985
- Truck Model
- K10
- Engine Size
- 350
None of the housing bolts hold the transmission in place. Those are only there to dampen vibration and be broken off with the ears. The transmission is sealed to the back of the block with a GM factory sludge that can be replicated when reinstalling with cooked 10W40. A 3' pry bar and a strong right foot kicking or a 5 lb maul banging at the tailshaft is all that is needed. You can check facebook marketplace under "Used Turbo 350 for sale" for confirmation.
