Swapping out OEM distributor with HEI distributor

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
I recently swapped out my OEM distributor with a HEI distributor. However, I noticed on the HEI distributor there's not a harness wire as on the OEM distributor. Although when I hooked up the new distributor without anything going to that wiring harness, everything is working fine. I'm trying to determine what is that wiring harness for on the OEM district
And omit this hookup to their wiring harness
The red distributor is the new HEI swap. The gray is the OEM distributor
You must be registered for see images attach
You must be registered for see images attach
 
PrairieDrifter

PrairieDrifter

Full Access Member
Joined
Dec 28, 2014
Posts
3,854
Reaction score
5,646
Location
North Dakota
First Name
Mason
Truck Year
84,79,77,76,70,48
Truck Model
Suburban k10, bonanza k10, k30, k20, c10, gmc 1/2ton
Engine Size
350, 350, 350, 350, 350, 350
Should be esc (electronic spark control) you don't need it. There should be a box under the dash. If it wasn't already moved.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,452
Reaction score
8,704
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
That harness was for the knock sensor computer ESC (electronic spark control)Your old distributor was HEI and knock sensor too,and also curved for your engine,assuming your engine is stock. If the factory distributor and knock sensor was working I'd prefer it on a stock truck. The knock sensor will allow you to run more timing because when it senses knock it starts pulling timing to eliminate it. A distributor without knock sensor you need to find the point just below knock and retard just a little more. Even on a performance motor my personal choice would be knock sensor recurved. If the old system had a problem I can see replacing it,kind of. But replacing it just for fun,wouldn't be my choice.
 
Last edited:
fast 99

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
2,029
Reaction score
2,938
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
Used GM is better than new. Where was that replacement distributor made?
 
TotalyHucked

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
3,671
Reaction score
11,863
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
As stated, that harness plug you're referring to is for the ESC computer (electronic spark control). The harness goes through the firewall and into a brain box that's mounted on the underside of the cowl, above the HVAC box. You're fine to run without it. Mine died and left me stranded in a parking lot in my '85. Once it cooled off, the truck would run so I limped it home, me and my dad yanked out the ESC dizzy and stabbed in a regular HEI. Reset the timing, adjusted the carb and touch and the truck drove so much better after that. 40yr old electronics are pretty much on their last leg by now
 
boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
Do I loose any power or spark not running the (esc)
Here's some recent pics of (HER) my 84 C10....well that's what the truck is referred to by my wife, because I spend the bank on (HER)
 

Attachments

  • PXL_20240921_210329376.jpg
    PXL_20240921_210329376.jpg
    160.7 KB · Views: 30
  • PXL_20240907_233051809.jpg
    PXL_20240907_233051809.jpg
    186.6 KB · Views: 24
  • PXL_20240907_233117243.jpg
    PXL_20240907_233117243.jpg
    193.5 KB · Views: 30
  • PXL_20240907_233056631.jpg
    PXL_20240907_233056631.jpg
    198.7 KB · Views: 25
  • PXL_20240907_233153023.jpg
    PXL_20240907_233153023.jpg
    262 KB · Views: 26
boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
The distributor is made by KMJ performance. The brand is called assault Racing. They're out of Iowa @fast 99
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,452
Reaction score
8,704
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
boloboss said:
Do I loose any power or spark not running the (esc)
Here's some recent pics of (HER) my 84 C10....well that's what the truck is referred to by my wife, because I spend the bank on (HER)
Click to expand...
If it was working correctly,yes you are giving up some power,and some gas milage,if it wasn't working right,you will be gaining.
 
boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
How would I tell if ithe old distributor wasn't working properly? I put in the new distributor, It seems like I'm getting more power as far as gas mileage. It seemed like it was burning a lot of gas before with the old distributor. I haven't determined the new gas mileage yet. @Ricko1966
 
Bextreme04

Bextreme04

Full Access Member
Joined
May 13, 2019
Posts
4,439
Reaction score
5,581
Location
Oregon
First Name
Eric
Truck Year
1980
Truck Model
K25
Engine Size
350-4bbl
Ricko1966 said:
If it was working correctly,yes you are giving up some power,and some gas milage,if it wasn't working right,you will be gaining.
Click to expand...
Only if he still had a stock 305. AFAIK the 350 never has ESC, it was only a stopgap for the piss poor head design of the 305 that made them an absolute dog with the small amount of timing you would need to set for it to not knock. If the engine has been replaced for a reasonably worked over 350, the ESC and 305 spark curve would be absolutely terrible on it.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,452
Reaction score
8,704
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
boloboss said:
How would I tell if ithe old distributor wasn't working properly? I put in the new distributor, It seems like I'm getting more power as far as gas mileage. It seemed like it was burning a lot of gas before with the old distributor. I haven't determined the new gas mileage yet. @Ricko1966
Click to expand...
You already swapped,at this point I wouldn't worry about it. Other wise you would need to swap the old one back in and do some checking on it.. Don't throw out your old parts. You may need them in the future
 
Last edited:
Bextreme04

Bextreme04

Full Access Member
Joined
May 13, 2019
Posts
4,439
Reaction score
5,581
Location
Oregon
First Name
Eric
Truck Year
1980
Truck Model
K25
Engine Size
350-4bbl
boloboss said:
How would I tell if ithe old distributor wasn't working properly? I put in the new distributor, It seems like I'm getting more power as far as gas mileage. It seemed like it was burning a lot of gas before with the old distributor. I haven't determined the new gas mileage yet. @Ricko1966
Click to expand...
Do you have a 350 now? Is it a stock 350 or somewhat warmed up? ESC was only on the 305 and it was necessary to get decent power and fuel mileage from them. If you now have even a stock 350 in it... you won't want the old 305 distributor. The spark curve and ESC will not work well on a 350.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,452
Reaction score
8,704
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Bextreme04 said:
Only if he still had a stock 305. AFAIK the 350 never has ESC, it was only a stopgap for the piss poor head design of the 305 that made them an absolute dog with the small amount of timing you would need to set for it to not knock. If the engine has been replaced for a reasonably worked over 350, the ESC and 305 spark curve would be absolutely terrible on it.
Click to expand...
I disagree but,don't want to argue about.
 
You must log in or register to reply here.

Similar threads

mjck5
hei distributor
2 3
Replies
34
Views
4K
1986_GMC C2500
1986_GMC C2500
T
Factory hei distributor and coil
2
Replies
15
Views
1K
txaggie
T
mjck5
hei vacuum advance stop plate
2
Replies
17
Views
3K
Turbo4whl
Turbo4whl
P
1978 k25 stalling issue
Replies
8
Views
385
Grit dog
Grit dog
Knep115
86 HEI no spark
2 3
Replies
31
Views
2K
Rustisbest
Rustisbest

Latest posts

Forum statistics

Threads
44,173
Posts
950,868
Members
36,288
Latest member
brentjo
Top