- Joined
- Dec 7, 2010
- Posts
- 24,744
- Reaction score
- 6,531
- Location
- Southeast PA
- First Name
- Paw Paw
- Truck Year
- 2007
- Truck Model
- Chevrolet Tahoe LT
- Engine Size
- 5.3, 4WD
Yikes.
Gas tank pressure problem
- Thread starter 77jimmy
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
blueburban87
Junior Member
- Joined
- Feb 11, 2022
- Posts
- 9
- Reaction score
- 17
- Location
- Fort Mill, sc
- First Name
- Chris
- Truck Year
- 1987
- Truck Model
- Suburban
- Engine Size
- 355
This is an old thread but looking for ideas on this as well.
I running into extreme tank pressure build up after my canister flooded with fuel so I bypassed it temporarily to try and track it down. I ran the evap hose back into a T to the overflow tub ( closed loop system) I know this is not the correct fix and its not fixing the pressure building up. Cap still sizzles with pressure. if the evap line is bypassed what else could it be?
Its a new sending unit, walbro 255LPH pump running a blue print engine Holley EFI setup.
I running into extreme tank pressure build up after my canister flooded with fuel so I bypassed it temporarily to try and track it down. I ran the evap hose back into a T to the overflow tub ( closed loop system) I know this is not the correct fix and its not fixing the pressure building up. Cap still sizzles with pressure. if the evap line is bypassed what else could it be?
Its a new sending unit, walbro 255LPH pump running a blue print engine Holley EFI setup.
Ricko1966
Full Access Member
- Joined
- Apr 11, 2017
- Posts
- 5,304
- Reaction score
- 8,441
- Location
- kansas
- First Name
- Rick
- Truck Year
- 1975
- Truck Model
- c20
- Engine Size
- 350
I'm not understanding where you've run your vent to. Pull the vent hose blow through the tube make sure it's clear to the tank. If it's clear,put a fuel filter in the vent hose for now it will allow the tank to vent,but will keep bugs and dirt out of the vent tube while you source a new evap cannister.
Last edited:
75gmck25
Full Access Member
- Joined
- Oct 13, 2016
- Posts
- 2,236
- Reaction score
- 2,155
- Location
- Northern Virginia
- First Name
- Bruce
- Truck Year
- 1975
- Truck Model
- K25 Camper Special TH350 NP203
- Engine Size
- 5.7
Go back to basics and check your sending unit and fuel pump fittings. The optimum solution for fuel flow and venting is a three port fuel pump (feed from tank, line to carburetor, return line back to tank), and a 3 port sending unit (feed to carburetor, return line in, vent line to canister), and a vapor canister under the hood.
If you threw your vapor canister and/or purge valve away in a moment of confusion, you can just zip tie or clamp the open rubber line up high on the radiator support and it will still vent.
The fuel feed and return lines should switch as you switch tanks, and the tank vent lines should be connected with a T and then run to the vapor canister.
If you threw your vapor canister and/or purge valve away in a moment of confusion, you can just zip tie or clamp the open rubber line up high on the radiator support and it will still vent.
The fuel feed and return lines should switch as you switch tanks, and the tank vent lines should be connected with a T and then run to the vapor canister.
Similar threads
Latest posts
-
-
-
Andi from Hannover/Germany with my 1985 C10 Stepside named "Daily-Blue1"- Latest: Corvette Ed
-
-