Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Camar068's latest activity
Camar068
replied to the thread
What new tools have you got lately?
.
I got the HF version. It comes in handy taking the front bumper off for sure. Don't forget to use anti-sieze when putting it back on.
Dec 3, 2024
Camar068
reacted to
Mr Clean's post
in the thread
What new tools have you got lately?
with
Like
.
Went and got me something I have been wanting so I took advantage of Black Friday.
Dec 3, 2024
Camar068
reacted to
ChuckN's post
in the thread
What new tools have you got lately?
with
Like
.
New tool chest day for the garage reorganization. Took the truck of course, since it was dry outside.
Dec 3, 2024
Camar068
replied to the thread
What have you done to your square lately??
.
lol didn't they come from the factory like that? :D
Dec 3, 2024
Camar068
replied to the thread
Electronic Shift NP203/NP205 Doubler
.
Ok....gotta know the setup you've got there. What TC you got?
Dec 2, 2024
Camar068
reacted to
SquareRoot's post
in the thread
Electronic Shift NP203/NP205 Doubler
with
Like
.
Shift levers are manly. Push buttons are not.
Dec 2, 2024
Camar068
reacted to
WFarm's post
in the thread
What have you done to your square lately??
with
Like
.
It may be just me, but I like the fasteners to stand out. Unless it’s a special fastener I’ll stop by Valley Fastener and get stainless...
Dec 2, 2024
Camar068
reacted to
ali_c20's post
in the thread
Headlight wiring harness
with
Like
.
Get a relay harness or diy one. Takes the load of the headlight switch...
Nov 19, 2024
Camar068
replied to the thread
Best way to run power from truck battery to trailer winch. Quick disconnect ends.
.
Thats what I used on both ends of the wiring going to the wench in the bed.
Nov 18, 2024
Camar068
reacted to
Grit dog's post
in the thread
Best way to run power from truck battery to trailer winch. Quick disconnect ends.
with
Like
.
Something like this and byor (buy your own wire). There’s pre-made winch cable kits as well. Presumably rated for the amp draw...
Nov 18, 2024
Camar068
reacted to
JD Miller's post
in the thread
Thread sealant on header bolts?
with
Like
.
seal 'em from what? Ive put grease or anti seize on 'em to keep from rusting stuck and breakin' off when removal time comes
Nov 18, 2024
Camar068
reacted to
KenHen's post
in the thread
Blower motor relay diode
with
Like
.
In case anyone has had problems with a new blower motor relay... I was having a problem with getting my blower motor to work, and it...
Nov 12, 2024
Camar068
replied to the thread
What have you done to your square lately??
.
In the 90's my camaro had cherry bombs. Believe it or not...they weren't that loud until higher rpms Recently I had 2 thrush...
Nov 10, 2024
Camar068
replied to the thread
This one needs to go, asking for opinions. Offering it up here first.
.
@donnieray wish I had 5k to spare. $500 for gear change, engine swap (to me) should be expected in most of these trucks so I don't fret...
Nov 6, 2024
Camar068
reacted to
Bextreme04's post
in the thread
What have you done to your square lately??
with
Like
.
I rebuilt mine a few years ago because it was leaking around the input shaft. I did a full rebuild and then did the proper adjustments...
Nov 6, 2024
Latest posts
1986 New member in Az
Latest: legopnuematic
11 minutes ago
Introduction
Pro Flo 4 with Delphi FE0114 or ACDelco EP381
Latest: Doppleganger
Today at 6:33 AM
TBI & EFI Conversions
Drop pittman arm or raised steering arm or both
Latest: 78 squarebody
Today at 6:03 AM
Lifted & Off-Road Systems
R
No accessories power
Latest: Ricko1966
Today at 3:57 AM
Electrical & Audio
Forum statistics
Threads
44,416
Posts
957,124
Members
36,753
Latest member
TheRigLivesOn
Members
Top