Recent content by Bloodhound1981
-
B
AC system recommendations
Another vote for VA from me. The install was straightforward and it performs very well.- Bloodhound1981
- Post #10
- Forum: Heat & AC
-
B
Check out my rear end
Just to update this thread, yesterday I picked up my truck from the differential shop. Ended up doing a full rebuild, axles and bearings, posi springs, clutches, ring and pinion. I switched from 3.73's to 4.11's, since it needed a ring gear cause there was pitting on it. It's perfect now as far...- Bloodhound1981
- Post #36
- Forum: Differential & Driveline
-
B
Reverse light options
Sadly, this is not the case. There are a number of proposed bills in the MA legislature proposing this, and another proposing eliminating safety inspections for vehicles over 45 years old, but they are still just proposed bills. I would be thrilled, my 1966 Porsche and my 1981 C-10 would be...- Bloodhound1981
- Post #26
- Forum: Electrical & Audio
-
B
Vent Window rubber replacement or replace?
Send to Precision for a rebuild and the win.- Bloodhound1981
- Post #15
- Forum: Tech Discussion
-
B
Do I even need a gas tank vent tube?
That is the setup I have on mine, but that's because I relocated the tank to the rear with a blazer tank, and my fuel filler is now in my bed. I have a vent hose going from the tank into the top inside of the wheel well, with a filter on it. As long as the height of the vent is higher than the...- Bloodhound1981
- Post #2
- Forum: Engine & Performance
-
B
Bucket buddy seats
That address comes back to this upholstery company "Stitch Upholstery". https://stitchupholsteryaz.com/- Bloodhound1981
- Post #6
- Forum: Introduction
-
B
POR 15 equivalents?
I wire wheeled and flap disked to bare metal, and followed their directions. This was in 2017, it has held up perfectly.- Bloodhound1981
- Post #12
- Forum: Garage
-
B
****CAUTION, PLEASE READ****
Agreed! Face to face with cash is what I always say. I was just sharing one I expected to be a scam but chose to entertain that worked out.- Bloodhound1981
- Post #30
- Forum: Wanted
-
B
POR 15 equivalents?
KBS Coatings https://www.kbs-coatings.com/?srsltid=AfmBOoqlw7gk1EiIk5zTyUNl4kjuQB_YkpZ6VUjLjibYsat9dxUmiEXL- Bloodhound1981
- Post #6
- Forum: Garage
-
B
****CAUTION, PLEASE READ****
I did something I would tell everyone else not to do, and luckily it all still worked out, which is nice. I have had a set of stainless Hooker headers posted on craigslist and FB for a while. They are for the 88-98 trucks, I had them on my '81 C-10 for less than a thousand miles but the driver...- Bloodhound1981
- Post #28
- Forum: Wanted
-
B
Stolen!
This is what I have for GPS tracking. It's $100 a year, but that's cheap insurance to know I won't lose my truck I've had since high school. Battery powered, which last at least 5 years, and uses GPS and 5G LTE. You can track it on an app, set up a geofence, etc...- Bloodhound1981
- Post #25
- Forum: Introduction
-
B
Holley / Brothers trucks clearance sale
There's a ton of stuff on there that I bought in the last year. Man I would have saved a ton of money at these clearance prices.- Bloodhound1981
- Post #8
- Forum: Exterior
-
B
Sound dampening
I definitely agree with the Kilmat on the outer door panel. You don't need to use a lot, there or anywhere else. I put one sheet inside each door and totally killed the tin sound. I did the roof as well before adding the headliner, and you don't have to go crazy over every square inch to get...- Bloodhound1981
- Post #3
- Forum: Interior
-
B
Hello from Northern MA!
Welcome from eastern MA! Great you still have her! (And the wife too) :)- Bloodhound1981
- Post #11
- Forum: Introduction
-
B
A new comer with a problem
My whole 8 foot fleetside bed, other than the wheel wells and tailgate, is aftermarket. I got the bedsides from LMC, it feels and looks original.- Bloodhound1981
- Post #11
- Forum: Introduction
