Search results

  1. Nasty-LSX

    I never knew how hot P/S fluid gets. New conversion. Pic's inside.

    I took off my Holley mid mount and LS3 intake. I am replacing with a billet front drive and TBSS intake (more torqe) I put a new P/S pump and and good size cooler because I constantly spin this baby to 6800 RPM. I had it full of fluid and in the cooler also. I let this motor run for about a...
  2. Nasty-LSX

    P/S pump pressure side fitting size on 97/07. Want to convert to AN fitting (pic's)

    I am updating the stepside LS FEAD. Removing the holley and putting a billet drive. I got a P/S cooler for this setup and need a AN fitting for the pump. How do I find the size of the pressure fitting as I dont have a old hose to go by. Here is the new swap if you have not seen it yet...
  3. Nasty-LSX

    Transfer case support brace. Who got one to sell?

    Are these all the same for K10 K20? I have a 208 with a 700R4 thats missing the brace. What shoulkd I look out for when buying this from someone?? Thanks :cheers:
  4. Nasty-LSX

    31x10.5 with 3:73 gears.700R4 trans. What RPM will I have at 70MPH?

    I know the final gear ratio on the 700R4 is 0.696. Or 0.70 So I got a k10 with 350 and 700R4 with a rear axle ratio of 3.73. I would Like to see 1800 to 2000 RPM at 70/75 MPH. So looking to get the right tires. Thanks!! :cheers:
  5. Nasty-LSX

    Windshield seal/rubber replacement. is there a preferred brand or is all the same?

    I need a windshield replacement. Are all rubber gasket windshield seals the same or is there a better brand to buy? Thanks
  6. Nasty-LSX

    Anybody collect hot rod magazines? look inside.

    I got about 500 to 700 mags of hot rod, hot rodding, super chevy, camaro performer, easyrider, hustler, cheri, swank, playboy, and many many more. all from the 80's to 2005. 99% in perfect condition and some, 1% may be missing a cover. I need to move these on. If there has to be a price per...
  7. Nasty-LSX

    Did I buy the right np241 TC for my truck??

    I dont know anything about transfer cases. Just want to make sure this is a squarebody TC. It is a pass side drop. It also has a mechanical speedo. I wanted a electronic one, but these are not a dime a dozen and dont pop up very often. Just want to make sure its chevrolet before I put a whole...
  8. Nasty-LSX

    Any Houston Members do Differential work. Who wants to play with my rear end???

    LMMFAO!!! Ok title is just a joke, I got a 87 10 bolt rear that pops when I turn. Pops so bad sounds like something is going to break. Never does it going forward. Rear end mechanics are freakin $$$$$$$$$$. Just wow. So I thought There might be a Houston Member that know how to do this kind of...
  9. Nasty-LSX

    C/K blazer tail light replacements from Amazon worth it? Take a look.

    I got new Tail light lens replacements from Amazon. The results will surprise you.
  10. Nasty-LSX

    86 C10 454 popping out exhaust soft and loud at times while in Idle. (WHY) Video inside

    I almost never drive it. It has good gas in it. It idles smooth, revs up great, drives fine. All of a sudden I get these soft and loud pops when its idling. What could be causing this? Turn your volume UP!!!
  11. Nasty-LSX

    73/87 are all skid plates the same for transfer case? Im looking for one.

    My k10 does not have one. I would like to put one on. I found a 1980 skid plate but want to make sure they are all the same, or if there are certain years for fitment. Thanks
  12. Nasty-LSX

    Rear wheels are sucked in way more than front. K10. Adapters? BAD IDEA? pics inside

    I know this is normal for k10/k20. Not sure the reason or why GM did this. I was once told it was due to the turning radius. My question is, Im guessing 1 1/2 inch adapters could correct this weird look. is there any negative to pulling the wheels out level with the fronts. I dont see why not...
  13. Nasty-LSX

    OBS seats in your Square. Who done it, Whats needed?

    Thinking of putting OBS seats in the K10, Whats needed to make this happen. Or just make my own brackets?
  14. Nasty-LSX

    Maxxis Mudder Buckshot II LT235/75R15 Brand new. Super Cheap!!

    These tires are new in perfect condition. These are not for me. $350.00 takes them. Houston TX
  15. Nasty-LSX

    Are locking hubs factory or personal add on?

    I'm still new to playing with 4x4's, but I ask because I remember my k20 came with locking hubs before I replaced them with warn hubs. The k10 just has caps on the end of the hubs. Got me thinking if they are aftermarket add on's. Thanks
  16. Nasty-LSX

    4x4 with 31x10.5/15 tire. Anyone running this size tire on stock lift??

    So I picked up a K10 with the original 6 lug rally wheels. That was one reason I wanted a 6 lug truck.(love the rally wheel look) I wanted to have a stock look (factory look) on the outside, with all modern internal's on the inside. So tire size is my next debate. This will be a daily driver...
  17. Nasty-LSX

    Anything new for HEADERS for K10 K20 I need a new set.

    October 2016 I found the perfect set of headers for the K20. https://www.gmsquarebody.com/threads/i-found-the-perfect-headers-for-67-86-c10-k20.16911/ I just picked up a K10 with C10 headers on it. They had to pull off the front drive shaft to install this LOL. Just want to see if these are...
  18. Nasty-LSX

    Rear aftermarket bumper (FARM LIKE) Nice bumper. Come get it!!

    Its like a farm truck bumper. Not my taste. $50.00 takes it. Come get, or can ship!! Need a repaint. there is a brand on it, but im not at the truck to see who makes it. Ask me later if interested.
  19. Nasty-LSX

    73/87 front push bar. Clean no dents or bends. CHROME. Come get it!!!!

    Not sure on who makes it or what year its from. $50.00 takes it. Come get it, or can ship. Let me know :happy160:
  20. Nasty-LSX

    How do I find out if I have 11 or 13 inch brakes

    1985 4x4 k20. I noticed some brake master cylinder replacements say for 11in and 13in brakes. Im replacing the brake master cylinder and want to get the correct one. Not sure if they are talking about the front or rear brakes
  21. Nasty-LSX

    Brake Master Cylinder, what adapters do I need to make this work? Pic's inside.

    I looked all over online to find out what size front and rear brake line port size is for my 85 K20 and my 86 stepside. NO LUCK FOR INFO!! The k20 has a all cast steel body and steel lid. the 86 has a aluminum body with a plastic resevoir. I bought the brake master cylinder on amazon and it said...
  22. Nasty-LSX

    I need a good 84/87 steering column.

    I need a decent one. I had to change the key switch out on the Stepper and when I put it back together my steering wheel feels like it wants to fall off now LOL.
  23. Nasty-LSX

    1985 K20. Need inspection to get tags. How to wire external horn button?

    My horn does not work. Im going to wire in a small horn button. What is the best easiest way to wire it up without running a wire all the way to the horn? Anyone know the horn wire color running into the column? How have you done it. Thanks :happy160:
  24. Nasty-LSX

    NEIKO 40447A LED Cordless under hood work light... UPDATE LOOK AT THIS!!!!

    Damn this this is awesome. If you watch the video you know about the light. The demo I did sucked compared to using it like this, I took pic's from 30 feet away and could see clearly. Best light ever. Like I said. You get what you pay for! This was on low setting
  25. Nasty-LSX

    Are rubber valve cover gaskets JUNK? Pic inside

    I did something I told myself I was not going to do. Put Chrome valve covers on. I put a weiand stealth intake on the truck and then said to hell with it and bought Chrome valve covers on it. I went to COMPETiTiON SALES I bought all the rubbers and breather and gaskets. When I got home and...

Latest posts

Forum statistics

Threads
42,322
Posts
913,640
Members
33,820
Latest member
tweeter68
Top