Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Turbo4whl's latest activity
Turbo4whl
reacted to
idahovette's post
in the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
with
Like
.
I kept most of my machines when I closed my shop. I have my Accuturn brake lathe and still do my own when needed. I also do some friends...
Apr 28, 2024
Turbo4whl
replied to the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
.
This is my point exactly. No one asks to have rotors or drums cut now. The old established stores have people that knew how to cut a...
Apr 28, 2024
Turbo4whl
reacted to
Bloodhound1981's post
in the thread
87 K10 Original seats?
with
Like
.
Not original.
Apr 28, 2024
Turbo4whl
replied to the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
.
Yes. Each truck manufacture lists their procedure for brake "break-in". Brake manufacture Meritor, who makes lots of brakes for many...
Apr 27, 2024
Turbo4whl
reacted to
Bullet Bob's post
in the thread
Changing front rubber brake lines. Where’s the inner clip?
with
Like
.
I’ve got a small electric one but it doesn’t cut it when it comes to 43 years worth of caked oil and grease. Pretty sure my grandfather...
Apr 27, 2024
Turbo4whl
replied to the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
.
Yes, they are cheap junk too. My 2 cents: I know it's hard to find someone to resurface those rotors. Clean and inspect your bearings...
Apr 27, 2024
Turbo4whl
reacted to
AuroraGirl's post
in the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
with
Like
.
only recent advances allow those bearings to go without a spindle of some kind, or shaft, which applies preload on the bearings. The OEM...
Apr 27, 2024
Turbo4whl
reacted to
bucket's post
in the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
with
Like
.
Older trucks have completely different front suspensions between 2wd and 4x4. It's not at all like most modern trucks with IFS and unit...
Apr 27, 2024
Turbo4whl
reacted to
bucket's post
in the thread
How can i separate my rotor from hub? Looks like its all one piece need help!
with
Like
.
What rotors did you buy? Sounds like you bought rotors for a 4x4. 2wd trucks have a 1-piece rotor/hub.
Apr 26, 2024
Turbo4whl
reacted to
creich68's post
in the thread
91 Burban Radio Restoration - Static Gone!
with
Like
.
Hello all! Awhile back I had posted about speaker ohm, thinking the static/crackling I was getting on the right channels was a...
Apr 26, 2024
Turbo4whl
reacted to
DoubleDingo's post
in the thread
Engine lift points
with
Like
.
Those are perfectly fine to lift an engine, that's all I've used. You'll be okay remove or stab the engine with those and a chain. I...
Apr 25, 2024
Turbo4whl
replied to the thread
I need a donut
.
Sun dial wrist watch, I want one!
Apr 24, 2024
Turbo4whl
reacted to
Frankenchevy's post
in the thread
I need a donut
with
Like
.
Apr 24, 2024
Turbo4whl
reacted to
chrisd9997's post
in the thread
Jumping in - 86 k10 long bed (first square body)
with
Like
.
Haven't even had it a week and I spotted a T-case leak.
Apr 24, 2024
Latest posts
Engine Stalling - Bad EVAP/Charcoal Canister?
Latest: legozombie
2 minutes ago
Carb Fuel Systems
Advice and Parts recommendations for some 6.2 cam/valvetrain work?
Latest: Bextreme04
5 minutes ago
Engine Swaps (Gas) LS, Vortec, LT1 , etc.
1983 Chevy K10 Cab Search
Latest: Grit dog
35 minutes ago
Paint and Body
C
A family heirloom
Latest: CmuCmu
39 minutes ago
Introduction
7
HEI ignition module relocation
Latest: 76 C20
45 minutes ago
Engine & Performance
Forum statistics
Threads
42,324
Posts
913,733
Members
33,824
Latest member
iamberttt
Members
Top